background image

 

 

PARTS INCLUDED 

 

A.  3400JF Aerating Fountain (Unit with cord or unit with 

Disconnect) (1) 

A1. Cord in separate box (1) (depending on size of cord) 
B.  Control Box (C-25 for 120V units in Float box or C-85 

for 240V units in separate box) (1) (Not Pictured) 

C.   Float (with two 50’ mooring ropes attached) (1) 
D.   1/4-20 x 3 1/4” Phillips Pan Head Screw (4) 
E.   1/4” (3/4” outer diameter) Flat Washer (4) 
F.   3/8” Flat Washer (4) 
G.  3/8”-16 Nylon Lock Nut (2) 
H.  3/8”-16 x 1-3/8” Hex Head Bolt (2) 
I.    Bottom Screen Clips (2) 
J.    Nylon Cable Tie 
K. Bottom Screen 
L.  Set of 5 Interchangeable Nozzles (5) (Diagram to Right) 
 

1.  3/8” x 2.25” bolt (1) 

 

2.  3/8” x 4” bolt (1) 

 

3.  Linden Nozzle (1) 

 

4.  Sequoia Nozzle (1) 

 

5.  Juniper Nozzle (1) 

 

6.  Willow Nozzle (1) 

 

7.  Cypress Nozzle (1) 

 

8.  Collar for Cypress Nozzle (1) 

M.  Mooring Rope Weights (2) 
 

TOOLS & SUPPLIES NEEDED 

 

A.  Anchors or stakes for installing unit (2) 
B.  # 2 Phillips head screw driver  
C.  120V or 240V Electrical Supply near pond on a post with room for mounting the C-25 or C-85  
G.  #10 x 1” long or longer screw(s) for mounting the 

C-25 (3) or C-85 (4) 

H.  9/16” Socket and Ratchet  
I. 9/16” 

Wrench 

 
 
 
 
 
 
 
 
 

UNIT SPECS. 

Model   

Voltage 

Operating 

  Lock Rotor   

Control Box   

Fountain Power 

    Amps 

  

 

Amps 

  Connection 

 Connection 

3400JF              110-120 

6.5 @ 120V    18 @ 120V   

C-25 Plugs In   

Plug into C-25 

3400HJF 

208-240 

2.9 @ 240V    9 @ 240V 

 

C-85 Hardwired 

Plug or Hardwire

 

 

 

 

 

 

 

 

 

at shore 

 

into C-85 

Power Cords 

Model Length Voltage Gauge 

Cord Shipped 

Seperately 

3400JF 

50 

120 

16 

No 

3400JF 

100 

120 

14 

No 

3400JF 

150 

120 

12 

Yes 

3400JF 

200 

120 

12 

Yes 

3400HJF 

50 

240 

14 

No 

3400HJF 

100 

240 

14 

No 

3400HJF 

150 

240 

12 

Yes 

3400HJF 

200 

240 

12 

Yes 

Summary of Contents for 3400HJF


















Reviews: