background image

12 

English

Park the appliance on an even surface.

Illustration 

Push the high pressure hose into the quick cou-
pling until it locks audibly.

Check the secure connection by pulling on the high 
pressure hose.

Insert the mains plug into the socket. 

For connection values, see type plate/technical data.
Observe regulations of water supplier.

ATTENTION

Impurities in the water can damage the high-pressure 
pump and the accessories. For protection, the use of 
the KÄRCHER water filter (optional accessory, order 
no. 4.730-059) is recommended.

Attach the water supply hose to the coupling on the 
water connection.

Connect the water supply hose to the water supply.

Completely open the water tap.

ATTENTION

Dry running of more than 2 minutes leads to damage of 
the high-pressure pump. If the appliance does not build 
up pressure within 2 minutes, switch the appliance off 
and proceed in accordance with the instructions in 
Chapter "Troubleshooting".

CAUTION

Keep a distance of at least 30 cm when using the jet for 
cleaning painted surfaces to avoid damage.

Push the spray lance into the trigger gun and fasten 
it by turning it through 90°.

Turn on the appliance “I/ON”.

Unlock the lever on the trigger gun.

Pull on the lever of the trigger gun; the device will 
switch on.

Note:

 Release the lever of the trigger gun; the de-

vice will switch off again. High pressure remains in 
the system.

DANGER

When using detergents, the material data safety sheet 
issued by the detergent manufacturer must be adhered 
to, especially the instructions regarding personal pro-
tective equipment.

With powerful foam for effortless cleaning.
Illustration 

Fill the detergent solution in the detergent tank of 
the foam nozzle (observe dosage instructions on 
the packaging of the detergent).

Connect the detergent tank to the foam nozzle.

Connect the foam nozzle to the trigger gun.

Note:

 This will mix the detergent with the water 

stream.

Spray the detergent sparingly on the dry surface 
and allow it to react, but not to dry.

Spray off loosened dirt with the high pressure jet.

Release the lever on the trigger gun.

Lock the lever on the trigger gun.

During longer breaks (more than 5 minutes), also 
turn the appliance off using the "0/OFF" switch.

CAUTION

Only separate the high-pressure hose from the trigger 
gun or the appliance when there is no pressure in the 
system.

Release the lever on the trigger gun.

Turn off the appliance "0/OFF".

Disconnect the mains plug from the socket.

Turn off tap.

Press the lever on the trigger gun to release any re-
maining pressure in the system.

Lock the lever on the trigger gun.

Detach the appliance from the water supply.

CAUTION

Risk of personal injury or damage! 
Mind the weight of the appliance during transport.

Lift appliance by the carrying handle and carry it.

Secure the appliance against shifting and tipping 
over.

CAUTION

Risk of personal injury or damage! 
Consider the weight of the appliance when storing it.

Prior to extended storage periods, as during the winter, 
also observe the instructions in the Care section.

Park the machine on an even surface.

Illustration 

Engage the spray lance in its holder.

Illustration 

Insert the trigger gun in its holder.

Suspend the high-pressure hose into its holder.

Roll up the power cord and loop it e.g. round the 
handle.

ATTENTION

Appliances and accessories that are not completely 
drained can be destroyed by frost. Completely drain ap-
pliance and accessories and protect them against frost.

To avoid damage:

Completely drain all water from the appliance: 
Switch the appliance on with detached high pres-
sure hose and detached water supply (max. 1 min-
ute) and wait, until no more water exits at the high 
pressure connection. Turn off the appliance.

Store the appliance and the entire accessories in a 
frost free room.

Start up

Water supply

Operation

High pressure operation

Operation with detergent

Foam nozzle

Recommended cleaning method

Interrupting operation

Finish operation

Transport

When transporting by hand

When transporting in vehicles

Storage

Storing the Appliance

Frost protection

Summary of Contents for K 25 Silent





















Reviews: