Kärcher Cuda 4860 Series Operator'S Manual Download Page 14 | Manualshive

Page: 14 / 56

background image

14

Operations

Oil Skimmer System

The oil skimmer system is located on the right rear
corner of the machine. It automatically removes oil from
the wash solution to prolong its useful life. Refer to
Using the Oil Skimmer for detailed operating instruc-
tions.

Air Flow Valve (Optional)

The air flow valve is located on the right rear corner of
the machine. It is a three-way ball valve that controls
the flow of compressed air to the power brush and the
hand detail brush.

Detail Tray and Sump Assembly (Optional)

Detail Tray

The detail tray is located on the right side of the
machine. The tray folds down to provide a convenient
work area for using the power brush and hand detail
brush. The weight capacity of the detail tray is 75
pounds.

Detail Sump

The detail sump is located below the accessory tray on
the right side of the machine. It provides wash solution
for the detail brush. The detail sump will hold approxi-
mately two gallons of wash solution.

Power Brush (Optional)

The power brush is located on the right front corner of
the machine. Refer to for detailed installation informa-
tion.

Cuda 4860 Operator’s Manual 8.914-383.0 - U

To Air

Supply

To Air

Supply

Outlet

To Detail

Brush

Outlet

To Power

Brush

Position 2:

Detail

Brush

Position 1:

Power
Brush

Detail

Brush

Power

Brush

Detail
Sump

Fold Down

Detail Tray

Skimmer

Disk

Skimmer

Motor

Wiper

Blades

Oil

Container

Throttle

Lever

Power Brush

Holding Bracket

Throttle

Lever Lock

All manuals and user guides at all-guides.com

«
...
12
13
14
15
16
...
»

Summary of Contents for Cuda 4860 Series

























































Reviews:

No comments

Related manuals for Cuda 4860 Series

Lavadora EMW580E3

Brand: EAS Electric Pages: 69

Brand: EAS Electric Pages: 138

Brand: NEFF Pages: 52

Brand: V-ZUG Pages: 4

Brand: V-ZUG Pages: 7

Brand: V-ZUG Pages: 2

Brand: Omega Pages: 32

NAGOLD SERENE FI02

Brand: Hafele Pages: 59

Brand: Indesit Pages: 16

Brand: Lavor Pages: 64

Brand: Maytag Pages: 52

Brand: NEFF Pages: 52

Brand: Hisense Pages: 34

Brand: NEFF Pages: 60

GU2275XTVY - 24" Wide Energy ST

Brand: Whirlpool Pages: 2

Brand: Samsung Pages: 44

Brand: Samsung Pages: 24

Brand: Samsung Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands