Kärcher Cuda 4860 Series Operator'S Manual Download Page 18 | Manualshive

Page: 18 / 56

background image

18

Maintenance

Maintaining The Machine

To ensure optimum performance and trouble-free oper-
ation, observe the following maintenance schedule
consistently.

Daily Maintenance

•

Check the water level; add water if necessary.

•

Clean the debris screen.

•

Remove oil from the wash solution using the oil
skimmer system (See

Using the Oil Skimmer

System

).

Weekly Maintenance

•

Examine the spray nozzles; clean and align if
necessary (See

Cleaning and Aligning the

Spray Nozzles

).

•

Wipe down the exterior of the machine using
spray degreaser and a soft, damp cloth. TO
PREVENT ELECTRICAL COMPONENT
FAILURE, DO NOT SPRAY THE MACHINE
WITH WATER.

NOTE: Spray degreaser and a damp cloth will usually
remove all dirt and grime from the machine. For
particularly stubborn soap deposits, use a soft cloth
dampened with warm solution from the wash
chamber.

Monthly Maintenance

•

Clean out the sump chamber and detail sump
(See

Cleaning out the Sump

).

•

Lubricate the door spindle using high-quality
automotive grease. Add grease until it begins to
flow out of the joint beneath the grease fitting,
then wipe excess grease from the fitting and the
joint.

•

Lubricate the turntable bearing using high-
quality automotive grease. The grease fitting is
accessible through the turntable deck. Add 1–2
strokes of grease, then wipe excess grease
from the fitting.

Semi-Annual Maintenance

•

Lubricate the pivot pin on the turntable motor
assembly with machine oil or anti-seize.

•

Lubricate the upper and lower pump bearings
using high-quality automotive grease.

Do not

over grease the bearings

; over greasing could

cause premature failure.

•

For 5 HP pumps, add 1–2 strokes of grease
every six months; for pumps larger than 5 HP,
add 2–3 strokes of grease every six months.

Cuda 4860 Operator’s Manual 8.914-383.0 - U

Grease Fitting

Door Spindle

Grease

Fitting

Pivot Pin

Drive

Motor

Compression

Spring Assy.

Grease

Fitting

Grease

Fitting

All manuals and user guides at all-guides.com

«
...
16
17
18
19
20
...
»

Summary of Contents for Cuda 4860 Series

























































Reviews:

No comments

Related manuals for Cuda 4860 Series

Brand: Haier Pages: 23

Brand: Maidaid Halcyon Pages: 17

Brand: Kalamazoo Pages: 40

K 3 Premium Power Control

Brand: Kärcher Pages: 16

K 3 Premium Power Control

Brand: Kärcher Pages: 40

Brand: Winterhalter Pages: 11

MVWC300VW - Centennial Washer

Brand: Maytag Pages: 20

Brand: Mach Pages: 45

Brand: Galanz Pages: 10

Brand: Ramteq Pages: 12

Brand: Asko Pages: 32

Brand: Kuppersbusch Pages: 56

Brand: AYA Pages: 48

Brand: PowerPoint Pages: 19

Brand: Cub Cadet Pages: 72

Brand: CDA Pages: 40

Brand: Currys Essentials Pages: 32

Brand: Candy Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands