Kärcher Cuda 4860 Series Operator'S Manual Download Page 6 | Manualshive

Page: 6 / 56

background image

6

Safety

General Safety Information

WARNING: To reduce the risk of
injury, read operating instructions
carefully before using.

1.

Read the owner’s manual thor-
oughly. Failure to follow instruc-
tions could cause a malfunction
of the parts washer and result in
death, serious bodily injury and/
or property damage.

WARNING: This is a heated parts
cleaner. Use only nonflammable,
noncombustible, water-based
cleaning compounds in this
machine. Do not fill or contami-
nate with any flammable or
combustible material such as
gasoline, alcohol, mineral spirits,
etc. Drain parts to be cleaned of
any combustible or flammable

material before placing inside cabinet. Failure to
observe this warning will create an extremely
hazardous condition.

DANGER: Keep water away from
electric wiring or fatal electric
shock may result.

2.

All installations must comply with
local codes. Contact your electri-
cian, plumber, utility company or
the selling dealer for specific
details.

Install the machine in compli-

ance with the National Electric
Code. Connect to a properly sized lockable discon-
nect and ground machine using the grounding stud
inside the main electrical panel.

3.

Do not touch machine with wet hands or while
standing in water. Always disconnect the power
before servicing.

4.

Never make adjustments on machine while it is in
operation except those prescribed in this manual.

WARNING: Use extreme caution
when opening the door of this
parts washer. Hot water/detergent
vapors will be emitted. Stand
Back! Hot cleaning solution could
cause serious injury.

5.

Do not allow high concentra-
tions of flammable fluids, acids,
or caustics to be introduced into

this machine.

WARNING: Flammable liquids can
create fumes which can ignite
causing property damage or
severe injury.

6.

Do not locate this machine in the
vicinity of any flammable vapors,
liquids or solids.

7.

Before servicing the machine,
refer to all safety data sheets

(SDS’s) on the material identified in the waste
stream. You must comply with all warnings and
wear all protective clothing stated on the SDS.

8.

When the machine is working, do not cover or
place in a closed space where ventilation is insuffi-
cient. Avoid installing machines in small confined
areas.

9.

In cold climates, this parts washer will freeze if not
in operation and must be located in a heated enclo-
sure.

10. Running this machine without water will damage

the heating elements and will void the warranty.

WARNING: Eye protection, gloves
and foot protection must be worn
while loading and unloading parts.

11. Eye protection, gloves, foot

protection and other safety
devices must be worn when
loading and unloading parts to be
cleaned.

Cuda 4860 Operator’s Manual 8.914-383.0 - U

WARNING

READ OPERATOR’S

MANUAL THOROUGHLY

PRIOR TO USE.

OPERATIONS

SAFET

Y

MAINTENANCE

WARNING

RISK OF EXPLOSION:

AVOID FLAMMABLE

LIQUIDS.

DANGER

KEEP WATER

SPRAY AWAY FROM

ELECTRICAL WIRING.

WARNING

EXTREMELY HOT:

USE CAUTION WHEN

OPENING LID

WARNING

RISK OF EXPLOSION:

AVOID FLAMMABLE

LIQUIDS.

WARNING

USE PROTECTIVE

EYE WEAR, GLOVES

AND FOOTWEAR

WHEN OPERATING.

All manuals and user guides at all-guides.com

all-guides.com

«
...
4
5
6
7
8
...
»

Summary of Contents for Cuda 4860 Series

























































Reviews:

No comments

Related manuals for Cuda 4860 Series

Brand: Celsius Pages: 13

HG6085D137635QW

Brand: Hanseatic Pages: 82

Brand: Kärcher Pages: 20

Brand: Sealey Pages: 5

Brand: Kärcher Pages: 16

Brand: ROBINHOOD Pages: 15

Brand: Gaggenau Pages: 33

Brand: Brandt Pages: 42

Brand: Kärcher Pages: 244

Brand: Kärcher Pages: 248

Brand: Kärcher Pages: 250

Brand: Kärcher Pages: 248

Brand: Kärcher Pages: 150

Brand: McCulloch Pages: 7

Brand: Lumina Pages: 18

Brand: Candy Pages: 88

Brand: Hotpoint Pages: 16

Brand: Alliance Laundry Systems Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands