Kärcher Cuda 4860 Series Operator'S Manual Download Page 10 | Manualshive

Page: 10 / 56

background image

10

Operations

Installation

Before You Begin

To prepare to install the machine, choose an unob-
structed, level site that allows convenient access for
operators and maintenance personnel. Sources for
water and electrical power should be located near the
installation site.

If you have any questions regarding the installation,
please contact your dealer or call a customer service
representative. When contacting customer service
please refer to the machine identification tag inside the
front cover of this manual for detailed machine specifi-
cations.

Step 1: Make Electrical Connections

NOTE: All electrical installation tasks must be
performed by a licensed, professional electrician to
ensure safe and proper operation.

The installation

must comply with the National Electric Code and all
applicable state and local codes.

The machine can only operate on the type of elec-
trical power indicated on the electrical specifica-
tions tag.

Read and understand the electrical

specifications tag to determine the electrical power
requirements before installing the machine.

Step 2: Connect A Compressed-air Line
And Accessories

This step is required for machines equipped with the
optional power brush and hand detail brush. If your
machine does not have these options, skip the
following procedure.

NOTE: To ensure proper operation and to minimize
the possibility of premature component failure, make
sure the compressed air is supplied at 75 to 90 psi.
Manufacturer also recommends an in-line moisture
trap and an in-line lubricator on the main air supply
line. Refer to the documentation provided with the
power brush for more information.

1.

Remove the power brush from the box, install the
wire brush in the chuck, and connect the air hose.

2.

Familiarize yourself with the three-way air flow
valve, then install a fitting to accommodate a
connection to your compressed-air supply.

3.

Connect the shop compressed-air line to the
machine.

4.

Connect the hose from the power brush to the air
flow valve.

5.

Hang the power brush on the bracket mounted on
the right side of the machine.

Cuda 4860 Operator’s Manual 8.914-383.0 - U

GR

OU

ND

Terminal Block

Grounding

Lug

Outlet to

Power Brush

3 Way Air

Valve

Outlet to

Detail Brush

Outlet to

Compressed Air

All manuals and user guides at all-guides.com

«
...
8
9
10
11
12
...
»

Summary of Contents for Cuda 4860 Series

























































Reviews:

No comments

Related manuals for Cuda 4860 Series

K 3 Premium Power Control

Brand: Kärcher Pages: 16

K 3 Premium Power Control

Brand: Kärcher Pages: 40

Hydra-Clean 1235 800-268

Brand: Graco Pages: 24

Brand: Kärcher Pages: 112

Brand: Sandstrom Pages: 36

Brand: ZANKER Pages: 40

Brand: Pacific hydrostar Pages: 23

Brand: V-ZUG Pages: 68

Brand: Simpson Pages: 48

Dishwasher DWD1E

Brand: Smeg Pages: 28

Brand: Landa Pages: 24

Brand: Fisher & Paykel Pages: 40

Brand: montpellier Pages: 28

Brand: Daewoo Pages: 7

Brand: Samsung Pages: 7

Brand: Samsung Pages: 56

Brand: Samsung Pages: 80

Brand: Samsung Pages: 89

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands