USA
·
Only muse low-foaming, non-combustible cleaning agents which
do not contain generally health-hazardous substances.
Explicit reference is made to the risks of using highly flammable, com-
bustible, toxic, health-hazardous, corrosive or irritant substances.
Initial operation
·
Delivery, instruction on safety procedures, handling and mainte-
nance and initial operation are generally carried out by our authori-
zed specialist.
·
If this is not the case, the operator is responsible for instructing
machine users.
Commissioning/operation
Please remember that the voltage in the building being cleaned must
concur with that given on the machine’s type plate.
Assembly instructions
·
The motor head and bar are supplied separately packed.
·
First release the hexagon socket srews in the shaft adjustment unit
(17).
·
Then feed the bar (7) gently as far as it will go into the shaft ad-
justment unit (17).
·
Align the handle bar (1) parallel with the wheels (9), so that the
open side of the housing of the top shaft element (3) is facing to
the rear.
·
Then tighten the hexagon socket screws again.
·
Wind the electric cable (18) around the handle bar (a) and cable
hook (8).
Preparations for use
·
Grasp the handle bar (1) with both hands and tip the machine until
it is resting on both wheels (A).
·
Then wheel the machine to its place of work and plug the electric
cable into the power supply.
·
Lay the accessories (11), i.e. brush or drive plate with pad, on the
floor.
·
Now tip the machine back onto the wheels and push it over the
brush (or drive plate) until the drive star and brush flange are verti-
cally aligned. Lower the machine onto the brush (B).
·
Then squeeze the shaft adjustment lever (5) and lower the bar (7)
into its working position. Both arms should be extended loosely
downwards (C).
·
Align the machine horizontally above the working element (brush
or drive plate), press the switch lock (4) and press the brush motor
switch (2) briefly.
·
The accessory automatically engages.
Machine use
·
Press the brush motor swith (2) (to the right or left). The motor
starts.
·
If you raise the bar (7) slightly, the machine moves to the right (D).
·
If you lower the bar, the machine moves to the left (D).
·
If you keep the bar in its central position, the machine works on the
spot.
After use
·
Squeeze the shaft adjustment handle (5) and shift the bar (7) into
its vertical position.
·
Then tip the machine onto its wheels (9) and press the brush
motor switch (2) briefly. The accessory (11) disengages.
·
Remove the plug from the power socket and wind the electric
cable (18) around the handle bar (1) and cable hook (8).
Thorough cleaning the easy way with the BD44-180 / Duo-Speed
190 rpm :
·
For thorough cleaning, the single-disc machine is supplied with the
following accessories:
-
Liquid tank (13)
-
Scrubbing brsuh (11) or drive plate with black pad (19).
·
Fasten the tank to the mounting (14).
·
Slide the outlet hose (12) onto the water connector (16).
·
Fill the tank (13). Then fit the brush or drive plate with pad.
·
Control the flow of liquid with the tank lever (15) by pulling the
lever (15) upwards.
·
Vacuum the dirty wash solution a section at a time with a water
extractor.
Shampooing thoroughly and efficiently with
BD44-180 / Duo-Speed 190 rpm
·
For shampooing, the machine is equipped with the following ac-
cessories:
- Liquid tank; 0.3 Perlon shampooing brush or Sapur pad for textile
floorcoverings.
·
The working procedure is in principle the same as for thorough
cleaning.
·
Start the machine with the shampooing brush dry.
·
Meter a small amount of liquid until the bristles are saturated with
foam.
·
Run the machine with the rotating brush from right to left or vice-
versa.
Þ
Immediately after this, run the machine in the same way
in the reverse direction, but with an overlap of about a quarter of
the strip already treated (E.)
·
Only then run the machine in a spiral pattern over the shampooed
strips.
Þ
In doing so, work both strips at the same time (F.)
·
During shampooing it is highly advisable to immediately remove
the dirt-laden foam a section at a time with a water extractor.
Assembly instructions for Spraymaster
·
Fit the holder for the spray can to the bar (7) with the holder poin-
ting upwards and, when viewed from the operating side, to the left
(G).
·
Hook the spray can’s tongue onto the holder, pivoting the holder
back until the ball catch engages.
·
Then slide the spring clip over the shaft adjustment unit (7).
·
Attach the box on the right or left as desired (H).
·
Point the universal-jointed hose in the desired direction.
Routine cleaning
