26
| English
0 276 001 XXX | (17.1.11)
Bosch ebike Systems
Technical Data
Assembly
Inserting and Removing the Battery
For inserting and removing the battery in/from
the the eBike, please read and observe the bat-
tery operating instructions.
Inserting and Removing the Drive HMI
(see figure A)
To
insert
the drive HMI, place it turned by ap-
prox. 30° onto holder
2
and then turn it clock-
wise to the stop.
To
remove
the drive HMI, turn it approx. 30° an-
ticlockwise and pull it out of the holder
2
.
f
Remove the drive HMI when parking the
eBike, so that the drive cannot be used by
unauthorised persons.
Without the drive
HMI, the drive cannot be switched on.
Checking the Speed Sensor
(see figure B)
The speed sensor
9
and its spoke magnet
10
must be mounted in such a manner that the
spoke magnet, after a turn of the wheel, moves
past the speed sensor with a clearance of no
more than 17 mm, max.
Note:
If the clearance between speed sensor
9
and spoke magnet
10
is too large or if the speed
sensor
9
is not properly connected, the speed
indication
a
will fail, and the eBike drive will op-
erate in emergency mode.
In this case, loosen the screw of the spoke mag-
net
10
and fasten the spoke magnet to the
spoke in such a manner that it runs past the
speed sensor with the lowest clearance possi-
ble. When the speed is still not being indicated
in the speed indication
a
after this, please refer
to an authorised bicycle dealer.
Drive Unit
Drive Unit
Article number
0 275 007 000/
0 275 007 001
Rated continuous
output
W
250
Output torque, max.
Nm
50
Rated voltage
V=
36
Operating
temperature
°C
–5...+40
Storage temperature
°C
–10...+50
Degree of protection
IP 5K4K (pro-
tected against
dust and
splash water)
Weight, approx.
kg
4
Drive HMI
HMI
Article number
1 270 020 900
Operating
temperature
°C
–5...+40
Storage temperature
°C
–10...+50
Degree of protection
IP 5K4K (pro-
tected against
dust and
splash water)
Weight, approx.
kg
0.15
Lighting*
Rated voltage
V=
6
Power output
– Front light
– Rear light
W
W
2.4
0.6
* Not possible via the eBike battery in all country-spe-
cific versions, depending on the statutory regulations
OBJ_BUCH-1407-001.book Page 26 Monday, January 17, 2011 2:58 PM
Summary of Contents for BionX
