background image

HygroPort I.S. User’s Manual 

 

Table C.1 shows the status flags associated with each Bit of the status register.  If a 

status fl lag is set high then the associated condition exists.  If it is set low, then that 

condition does not exist. 
 

 

Details 

 

Reading out of range (beyond  

+30/-120ºC) 
Reading out of range (beyond  
+100/-40ºC) 

External Sensor Input out of range  
(<4 mA / >20 mA) 
Battery voltage <4.7 V 

Internal dewpoint not stable 

 

Internal dewpoint stable 

Log file has reached the maximum 
of 10,000 logs and logging has  
been stopped 
Could not detect internal sensor on  
power up 

Config. fi ile missing, new file  
created and default settings used 

Indicates system in purging phase 

 

Table C.1 

Status register flags 

 
For the example given in Figure C.1, from Table C.1, Hex 28 translates, reading from 
right  to  left,  as  Bit  4  set  (

External sensor error

)  and  Bit  6  set  (

Measurement in 

progress

).  Therefore, at the time that these log points were taken, the external sensor 

was out of range and the internal dewpoint was not stable. 
 
 
 
 
 
 
 
 
 
 
 
Issue 6, December 2019 

56 

Kahn Instruments 

Status Register 

Bit in Hex 

0x0002 = BIT 2 
 

0x0004=  BIT 3 

 

0x0008 = BIT 4 
 

0x0010 = BIT 5 
 
0x0020 = BIT 6 
 

0x0040 = BIT 7 

 

0x0080 = BIT 8 
 
 

0x0100 = BIT 9 

 

0x0200 = BIT 10 

 

0x0800 = BIT 12 
 

Message 

 

Internal sensor error 

Internal thermistor  
error 

External sensor error 

Battery low 
Measurement in  
progress 
Measurement OK 
 
Log finished 
 
Internal sensor not  
found 
Default CONFIG file  
Used 

Initializing internal 
sensor 

 

 

 

Summary of Contents for HygroPort I.S.







































































Reviews: