background image

ENG

ENG-15

Rear joint hook

Rear joint bar

(Between the shell 

and the liner)

Attachment of Cheek pads:

ATTACHING THE JOINT BAR

Rear joint hook

Joint bar

Push the middle of the cheek pad.

c

Push the middle of the cheek pad into 

the  trim  rubber  in-between  the  helmet 

shell and the liner.

Front Joint Hook

Flip the trim rubber up

Flip the trim rubber up

Chin liner

Cheek pad

Cheek pad

Snap

Be sure that the cheek pads are attached on the helmet securely before riding.

It is hazardous to use this helmet without cheek pads or attaching the cheek pads improperly. 

Fig. 1

Fig. 2

Fig. 3

Fig. 4

1 5

a

Insert the rear Joint Hook in-between the shell and the liner from the position shown 

in the figure, and hook it to the "Joint Bar" hidden inside there.

Attaching is 

complete

b

Flip up the rubber trim around the chin 

area as shown in Fig.2. Insert the front 

Joint  Hook  in-between  the  helmet  shell 

and  chin  liner  until  the  Joint  Hook  is 

fixed.

d

Let the chinstrap go through the chinstrap 

cover, then fasten 2 snaps and hook and loop 

fasteners at the back side of the cheek pad. 

Follow the same procedures on the other side. 

Push it into the 

direction of the 

arrow.

a

Turn it to the 

direction of the 

arrow. 

b

ATTACHING THE JOINT BAR

Rear joint bar 

(Between the shell 

and the liner)

Rear joint hook

Joint bar

Fig.1

Fig.2

Fig.4

Fig.3

Flip the trim rubber up

Front Joint Hook

Push the middle of the cheek pad.

Cheek pad

Snap

Chin liner

Insert the rear Joint Hook in-between the shell and the liner from the position shown 

e.

Flip up the rubber trim around the chin 

area as shown in Fig.2. Insert the front 

Joint Hook in-between the helmet shell 

CAUTION

Be sure that the cheek pads are attached on the helmet securely before riding. 

It is hazardous to use this helmet without cheek pads or attaching the cheek pads improperly. 

Let the chinstrap go through the chinstrap 

cover, then fasten 2 snaps and hook and loop 

fasteners at the back side of the cheek pad. 

Follow the same procedures on the other side. 

Push the middle of the cheek pad into 

the trim rubber in-between the helmet 

shell and the liner.

Attachment of Cheek pads:

Summary of Contents for Japan FF-5V




























Reviews: