Kaba Mas Unicon CL Series Operating Instructions Manual Download Page 5 | Manualshive

Page: 5 / 16

Kaba Mas Unicon CL Series Operating Instructions Manual Download Page 5

5

Lock Maintenance

Once you have receive the “battery Low” indication of ten
fast yellow flashes after a valid combination entry, you
should change the batteries in a reasonable amount of time.
Remove the two screws from the battery panel and then
remove the panel. Remove the CR-2 Lithium 3V batteries
and replace with high quality, name brand batteries
(Energizer

®

or Duracell

®

.) The negative (-) end of the

battery should be inserted into the battery cavity first.

WARNING:

The lock MUST NOT be sprayed with water or any cleaning liquid.

Recommended cleaning is to wipe down the lock using a damp cloth or a
towelette. Alcohol is an acceptable disinfectant for medical environments.

Initial Lock Operation

To test successful installation of the lock before you begin lock setup, perform the
following operation.

WARNING:

The container door should remain open until testing is complete.

To Lock/Unlock Using the Master/Manager Pre-Set PINs

Your lock has been shipped so that

any valid Master or Manager User ID for the

lock model followed by the factory pre-set PIN for that User ID will lock or unlock
the lock.

Lock the Lock - Master/Manager Pre-Set

1.

If necessary, turn the lock knob counter clockwise (CCW) to the “locked”
position.

2.

Press and hold the

key until the yellow light

Y

displays.

3.

Enter any valid three-digit User ID for the lock model followed by the default
factory PIN for the User ID. ( For

User ID 111

the default PIN is “

12345

”. For all

other Users IDs the default PIN is “

55255

”. )

If the combination is entered successfully, the lock displays one green flash

G

with a beep

to indicate that a valid combination has been entered. One long

green flash

G

displays with a beep

to indicate that the motor has fired and

the lock is in the “locked” state. A long red flash

R

is displayed with a beep

to indicate that the knob is in the closed position and the lock is locked.

Note:

A “combination locked state” audit record is written at this point followed by a “lock
close” audit record if the knob is in the “locked” position. If the knob is not fully

turned CCW to the “locked” position, the long red light

R

will not display at the end

of the operation and the “lock close” record will not be written.

Battery Panel

+

+

-

-

«
...
3
4
5
6
7
...
»

Summary of Contents for Unicon CL Series

















Reviews:

No comments