background image

16

Notice:

Information in this document is subject to change without notice. Kaba Mas shall not be liable

for technical or editorial errors or omissions contained herein; nor for incidental or consequential
damages resulting from the furnishing, performance or use of this material.

© 2007 Kaba Mas Corporation. All rights reserved.

PowerStar Technology, Auditcon, and Smart Key are registered trademarks of Kaba Mas Corporation in
the United States and/or other countries.

This product is covered by one or more of the following U.S. patents:

4,803,860 5,170,431 5,265,452 5,271,253 5,410,301 5,451,934 5,488,358 5,488,660

5,493,279 5,511,401 5,590,917 5,592,838 5,709,114 5,774,058 5,774,059 5,870,914

5,873,276 5,881,589 5,893,283 5,896,026 D366,822

D388,308

D388,309

Kaba Mas Corporation

749 W. Short Street, Lexington, KY 40508  USA

Phone:  (859) 253-4744  FAX:  (859) 255-2655

Technical Support: (800) 950-4744

www.kaba-mas.com

4.

Return the key fob to the Unicon CL Series Software PC to be read. Refer to the
software documentation for instructions on reading the reporting key.

Retrieve User Table

The lock’s User information reporting feature will allow retrieval of status information
for all administrative users in the lock.

Note:

The Retrieve User information operation requires a red reporting key fob that has
been initialized using the PC software to retrieve User information. When a user
table is retrieved, it will overwrite any previously existing user data that is in the key
fob.

The process for retrieving User Table information is the same as that for retrieving
audit information (The only difference is that the red reporting key fob has been
initialized to retrieve User Table information rather than Audit information). To retrieve
User Table information, perform Steps 1-4 in the previous “Retrieve Audit Records”
section.

Summary of Contents for Unicon CL Series

















Reviews: