background image

10

L

OCK

 O

PERATIONS

Operations found in this section are those that can be completed as needed in the course of
normal lock operation after the lock has been set up.

G

 

= Green Flash

   

R

 

= Red Flash

    

Y

= Yellow Flash

    

 

= Beep

Administrative User Operations

The following operations are those that should be completed by the Master and/or Manager
Users for administrative purposes.

Add Manager User(s)

The Master User can add a Manager User to the lock

Note:

A maximum of 124 Manager Users can be added to the lock.

1.

Press 

#

 

Y

 

and then 

4

G

R

2.

Enter the Master User combination. 

G

R

3.

Enter the new Manager User ID. 

G

R

4.

Enter the new Manager User ID again for verification. 

G

R

5.

If additional Manager Users are to be added, repeat Steps 3-4 until all Manager
Users have been added.

6.

Enter 

111

 to end the operation. 

G

R

  

G

R

Note:

The default PIN assigned to a new Manager User ID is “55255”. This default
PIN must be changed by the User before any lock operations can be per-
formed.

 Refer to the “Change PIN” section for instructions on changing a User PIN.

Delete Manager User(s)

Note:

A Manager User can only be deleted by the person who created the User (i.e., the
Master User.)

1.

Press 

#

 

Y

 

and then

 5

G

R

2.

Enter the Master User combination. 

G

R

3.

Enter the Manager User ID to be deleted.  

G

R

4.

Enter the Manager User ID to be deleted again for verification. 

G

R

5.

If additional Manager Users are to be deleted, repeat Steps 3-4 until all Man-
ager Users have been deleted.

6.

Enter 

111

 to end the operation. 

G

R

  

G

R

Change PIN

A user (Master or Manager User) PIN can be changed at any time (however, a User ID can
never be changed.)

Caution:

Before changing a PIN, open the container door to allow testing with the new PIN.

1.

Press 

#

 

Y

 and then 

1

G

R

Summary of Contents for Unicon CL Series

















Reviews: