JVC V.NETWORKS VN-C30U Instructions Manual Download Page 14 | Manualshive

Page: 14 / 60

background image

14

Installation and setup

1. Installation

Use the optional bracket (Model VN-BK30) for installation.
Make the power and network connections after completion of the instal-
lation work.

Caution

Install in a location with sufficient strength to prevent falling.
VN-C30U units can only be installed as shown in the diagram below, or
inverted. Do not install facing sideways.
Tilted installation is not possible.

1 Attach the ceiling fixer with the hole

pointing toward the front of the camera.

4 Mount the VN-C30U on the ceiling fixer

by rotating clockwise, then tighten the
screw of the camera body fixer.

2 Mount the camera body fixer

on the VN-C30U.

3 Attach the drop-prevention wire of the

ceiling fixer to the camera body fixer.

drop-prevention wire

V

.NETW

ORKS

V

.NETW

ORKS

«
...
12
13
14
15
16
...
»

Summary of Contents for V.NETWORKS VN-C30U





























































Reviews:

No comments

Related manuals for V.NETWORKS VN-C30U

Brand: Salus Pages: 2

Brand: i-PRO Pages: 2

NVIP-2VE-4231/PIR

Brand: Novus Pages: 36

Brand: CommBox Pages: 4

Panametrics Epoch 4 Plus

Brand: Olympus Pages: 188

VK2-3MPBIR28V12re

Brand: Vista Pages: 14

Brand: Guardian Pages: 2

Brand: XtendLan Pages: 33

Profi+ KH 2927-2

Brand: Powerfix Pages: 53

Brand: unotec Pages: 24

Brand: Eaton Pages: 36

Brand: Abus Pages: 220

Brand: TRIVIEW Pages: 5

Brand: V-TAC Pages: 10

Brand: Hitachi Kokusai Electric Pages: 6

Brand: Parker Pages: 13

Funke+Huster Fernsig TWIN-EExll

Brand: Eaton Pages: 4

Digiplex NE DGP-NE96

Brand: Paradox Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands