JVC MP-XP5230 Instructions Manual Download Page 97

Page: 97 / 126

If you forget the BIOS password
The following passwords can be set on the BIOS.

• User password

When this password is set, the user is requested to enter the password to start Windows
or change a BIOS setting.

• HDD password

The password required for accessing the hard disk.

Important

• You cannot delete the BIOS password even if you forget it. To delete it forcibly, you

have to return your PC to us for chargeable service. (It may require hard disk drive
replacement.)

• To bring up the BIOS menu, turn on the PC and press the Alt and F2 keys while the

JVC logo screen is shown.
Do not change the BIOS setting unless you have adequate knowledge of computers. A
wrong setting can make your PC unable to start up again or, worse, damage it.

Setting procedure does not complete.

If Internet, e-mail, or any other setting does not complete through the procedure described
in this manual, check the following.

• If the [Control Panel] display is in Classical mode, change it to the Category mode. All

the setting procedures in this manual assume the Category display mode.

XP72305230E-82-104

2/26/3, 8:57 AM

Summary of Contents for MP-XP5230































































































































Search results

Summary of Contents for MP-XP5230

Reviews:

JVC MP-XP5230, Instructions Manual, Page: 97 / 126

Search results

Summary of Contents for MP-XP5230

Reviews: