manualshive.com logo in svg

JVC MP-XP5230, Instructions Manual, Page: 68 / 126

Share
Download
JVC MP-XP5230 Instructions Manual Download Page 68

68

 EN

HARDWARE

Suggestions for using the wireless LAN

• Use the wireless LAN in a location where there are as few obstacles as possible.  To maximize

the distance over which communication with the wireless LAN is possible, open the display,
and point its reverse side (the side with JVC logo) at the access point.  Do not place any
obstacles such as books or thick stacks of paper between the PC and access point.

Setup procedure for the wireless LAN

Caution

In order to make it easier to check the operation of the PC’s wireless LAN, start the access point
before proceeding to use the wireless LAN in the infrastructure mode.  For use in the AdHoc
mode, start the PC that serves as the other end of the communication where the wireless LAN
settings have already been completed if possible before proceeding to use the wireless LAN in
this mode.

Wireless LAN antenna

Wireless LAN antenna

XP72305230E_66-81

2/25/3, 5:44 PM

68

Summary of Contents for MP-XP5230































































































































Reviews:

No comments