manualshive.com logo in svg

JVC MP-XP5230, Instructions Manual, Page: 78 / 126

Share
Download
JVC MP-XP5230 Instructions Manual Download Page 78

78

 EN

•

System in standby status

The built-in battery discharges whilst the PC is in system standby status.  As a result,
any unsaved data may be lost or the system may not start up.  Be sure to turn off the PC
when it is not used for a long time.
Under fully charged condition, the unit can maintain the system standby status for the
following periods.

1

About 20 hours with the built-in battery pack alone

2

About 55 hours with the built-in and standard battery packs

•

System in halt status

Continued operation on the PC displaying a battery-low warning causes the result as
follows:

1

When the halt status is enabled
The PC turns off while maintaining the current data.

2

When the halt status is disabled
The PC does not save the current data, which will be lost.

We recommend that you enable the halt status setting.  This function is enabled at the
factory.

HARDWARE

XP72305230E_66-81

2/25/3, 5:45 PM

78

Summary of Contents for MP-XP5230































































































































Reviews:

No comments