1-3
1
COVER (UNDER)
Fig.1-3-1 (S
1
)
—
2
COVER (SHOE)
Fig.1-3-2 2(S
2
), 2(L
2
)
—
3
MIC COVER ASSY
(S
3
a), 2(S
3
b)
—
4
UPPER CASE ASSY Fig.1-3-3a (SD CARD)
NOTE
4
a
(Inc.MONITOR ASSY)
NOTE
4
b
Fig.1-3-3b (S
4
a), (S
4
b), 3(S
4
c), 2(S
4
d), NOTE
4
c
2(S
4
e), (S
4
f),
NOTE
4
d
CN
4
a, CN
4
b
5
MONITOR ASSY
Fig.1-3-4 2(S
5
a), GUIDE(MONI), 2(S
5
b) NOTE
5
6
SHUTTER ASSY
Fig.1-3-5 (S
6
)
NOTE
6
7
BOTTOM ASSY
Fig.1-3-6 CN
7
, 2(S
7
a), 2(S
7
b), 3(S
7
c), NOTE
7
(S
7
d)
8
LOWER CASE ASSY Fig.1-3-7 CN
8
a, CN
8
b,
NOTE
8
(Inc. MICROPHONE,
SHEET(SHUTTER),
E.VF UNIT,
CN
8
c, CN
8
d, CN
8
e, 3(S
8
)
OP MDA BOARD
ASSY,SHOE ASSY,
OP BLOCK ASSY)
9
MAIN BOARD ASSY Fig.1-3-8 SHEET(SHUTTER), 2(S
9
)
—
(L
9
a), SHIELD ASSY, CN
9
a,
CN
9
b, CN
9
c, CN
9
d,
(L
9
b), CN
9
e, CN
9
f
0
MECHANISM ASSY
(S
0
a),BRACKET(PRE/REC),
3(S
0
b),BRACKET(MECHA) ASSY
!
MICROPHONE
Fig.1-3-9a —
NOTE
!
@
OP BLOCK ASSY
(S
@
), 2(S
$
a)
NOET
@
#
E.VF UNIT
(S
#
a), (S
#
b), CN
#
NOTE
#
a
NOTE
#
b
NOTE
#
c
$
OP MDA BOARD
Fig.1-3-9b 2(S
$
b), CN
@
NOTE
$
a
ASSY
NOTE
$
b
%
SHOE ASSY
CN
%
, 2(S
%
)
NOTE
%
STEP
No.
PART
Fig.No.
POINT
NOTE
1.3.2 Disassembly method
Table 1-3-2
NOTE
4
a:
If a card is installed, remove it in advance.
NOTE
4
b:
Be careful not to damage the battery removal switch.
When disassembling, ensure that the lock lever is in the
low position and set the battery removal switch only to
the up position.
NOTE
4
c:
A screw (14) is located inside the Cover (MULTI/USB).
NOTE
4
d:
Slide down the shutter and remove the screw (15).
NOTE
5
:
Refer to Fig. 1-4-1 for the disassembly method.
NOTE
6
:
Be careful not to damage or lose the parts.
NOTE
7
:
Take care of the removed screws.
NOTE
8
:
For the disassembly/assembly of the E. VF unit, Shoe
assembly, OP MDA board assembly, and OP block as-
sembly, see section 1.8, “SERVICE KNOW-HOW”.
NOTE
!
:
Leave the microphone connected to the OP block as-
sembly.
NOTE
@
:
Refer to Fig. 1-5-1 for the disassembly method.
NOTE
#
a:
Be careful not to cut the FPC wire or damage any of
the switches during work.
NOTE
#
b:
Refer to Fig. 1-6-1 for the disassembly method.
NOTE
$
a:
Be careful not to lose the parts.
NOTE
@
,
#
c,
$
b,
%
:
When assembling, attach the OP block assembly, E.VF
assembly and the shoe assembly on the OP MDA board
assembly and install them together in the lower case
assembly.
CONN.
No.
Pin No.
CONNECTOR
Note:
Remove the parts marked in .
CN
4
a MAIN
CN112
⇔
SUB OPE UNIT
-
8
CN
4
b MAIN
CN113
⇔
MONITOR
CN401
39/33
CN
7
MAIN
CN107
BOTTOM
CN301
50
CN
8
a MAIN
CN110
OP MDA
CN201
80
CN
8
b MAIN
CN111
⇔
CCD
-
20
CN
8
c MAIN
CN109
⇔
ZOOM OPE UNIT
-
13
CN
8
d MAIN
CN108
↔
EJECT SW
-
2
CN
8
e MAIN
CN115
↔
MICROPHONE
-
4
CN
9
a MAIN
CN102
⇔
LOADING MOTOR
-
6
CN
9
b MAIN
CN103
⇔
ROTARY ENCODER
-
6
CN
9
c MAIN
CN101
⇔
HEAD
-
8
CN
9
d MAIN
CN106
⇔
SENSOR
-
16
CN
9
e MAIN
CN105
⇔
CAPSTAN MOTOR
-
18
CN
9
f
MAIN
CN104
⇔
DRUM MOTOR
-
11
CN
@
OP MDA
CN204
⇔
OP BLOCK ASSY
-
24
CN
#
OP MDA
CN203
⇔
VF BL
CN7001
20
CN
%
OP MDA
CN202
⇔
SHOE ASSY
-
16/13
Table 1-3-3
