2-19
Fig. 2-8-1
2.8 COMPATIBILITY ADJUSTMENT
2.8.1
Jig connector cable connection
Remove one screw (1) first and the cover (JIG) next.
COVER
(JIG)
COVER
(M.ADJ)
GUIDE ROLLER
(SUP) ASSY
GUIDE ROLLER
(TU) ASSY
JIG CONNECTOR
CABLE
1
RED
to 6 pin
( JLIP_RX )
WHITE
BLACK
to 25 pin
( JLIP_TX )
to 15 pin
( GND )
JIG CONNECTOR COMMUNICATION CABLE
COMMUNICATION
CABLE
TO PC
CABLE
TO JIG CONNECTOR CABLE
2.8.2 Tape pattern check
(1)
Play back the compatibility adjustment tape.
(2)
While triggering the MAIN CN114-11PIN (HID1), ob-
serve the waveform of CN114-29PIN (ENV_OUT).
(3)
Confirm that the waveform is free from remarkable
level-down, and entirely parallel and straight.
Moreover, perform the following adjustment as re-
quired.
(4)
In case any level-down is observed on the left hand
side, straighten the level by turning the guide roller of
the pole base assembly (supply).
In case any level-down is observed on the right hand
side, however, straighten the level by turning the guide
roller of the pole base assembly (Take-up).
(5)
After adjustment, try the unloading motion once, and
confirm that the waveform is flat (straight) when the
tape has been played back again.
Moreover, perform readjustment as required.
(6)
When the recording has been played back again, play
back the self-recording to confirm that the waveform
is flat.
Fig. 2-8-3
Fig. 2-8-4
CN114-29
(ENV_OUT)
CN114-11
(HID1)
Flatten the waveform.
Misalignment of guide roller
height on the take-up side
Misalignment of guide
roller height on the
supply side
Note:
When an adjustment is performed with the lower case cover
attached, first slide the Cover (M.ADJ) open and then per-
form the compatibility adjustment.
Be sure not to damage the cover plate when sliding it open
to make an adjustment because it must be re-positioned af-
ter completing the adjustment.
NOTE)
The JIG connector board uses 30 of the 40 pins of
CN114 on the Main board.
Pins 1 to 5, 21 to 24 and 34 of CN114 on the Main board
are not used.
MAIN
CN114
VF_RPD
40
CVF_G
20
CVF_R
39
CVF_B
19
VF_COM
38
MT_RPD
18
MT_G
37
MT_R
17
MT_B
36
MT_COMCS
16
MT_PSIG
35
GND
15
GND
34
MONI_CHG
14
SBE
33
SPA
13
FRP
32
FS_PLL
12
DISCRI
31
HID1
11
ATFI
30
MAIN_VCO
10
ENV_OUT
29
PB_CLK
9
TRST
28
TCMK
8
TMS
27
TDO
7
TDI
26
JLIP_RX
6
JLIP_TX
25
IF_TX
5
AL_3VSYS
24
CJIG_RST
4
VPPC
23
SRV_RX
3
SRV_TX
22
REG_3V
2
DRST
21
VPPD
1
JIG CONN. BOARD
(PIN NO.)
40
VF_RPD
39
CVF_R
38
VF_COM
37
MT_G
36
MT_B
35
MT_PSIG
33
SBE
32
FRP
31
DISCRI
30
ATFI
29
ENV_OUT
28
TRST
27
TMS
26
TDI
25
JLIP_TX
20
CVF_G
19
CVF_B
18
MT_RPD
17
MT_R
16
MT_COMCS
15
GND
14
MONI_CHG
13
SPA
12
FS_PLL
11
HID1
10
MAIN_VCO
9
PB_CLK
8
TCMK
7
TDO
6
JLIP_RX
Fig. 2-8-2
