Masterpage:Right+
EN
45
Filename [MV5SEK_08Basic TimerDub.fm]
EDITING
Page 45Wednesday, 31 August 2005 19:58
L-2 Select Setting
Set “L-2 SELECT” to the appropriate mode depending on the type
of appliance connected to the unit’s [L-2 IN/DECODER] connector.
1
Perform steps
1
and
2
of “L-1 Output And L-1 Input Setting”
(
墌
pg. 44).
2
Press
rt
to select “L-2 SELECT”, then press
ENTER
.
3
Press
rt
to select the
appropriate setting, then press
ENTER
.
4
Press
SET UP
to complete the
setting.
NOTES:
●
If “L-2 SELECT” is set to
“S-VIDEO/RGB”, it is not possible
to output colour signals correctly
from the VHS deck.
●
If “L-2 SELECT” is set to “DECODER”, only the DVD deck operates
properly.
* The
boldface
settings below indicate the settings at your purchase.
8
L-2 SELECT
—
VIDEO/RGB
/ S-VIDEO/RGB /
SAT VIDEO/RGB / DECODER
Select “VIDEO/RGB” or “S-VIDEO/RGB” to use this unit as the
recording deck with the player connected to the [L-2 IN/
DECODER] connector, or to use the satellite receiver connected to
the [L-2 IN/DECODER] connector.
VIDEO/RGB
: If a connected appliance’s output is compatible with
regular video signals, set to “VIDEO/RGB”.
S-VIDEO/RGB
: If a connected appliance’s output is compatible with
Y/C signals, set to “S-VIDEO/RGB”. You can obtain high-quality
picture. (For connection, be sure to use a 21-pin SCART cable
that is compatible with the Y/C signal.)
Select “SAT VIDEO/RGB” to view a satellite programme with the
TV set while the unit is turned off. (
墌
pg. 76)
SAT VIDEO/RGB
: If a connected satellite receiver’s output is
compatible with regular video signals, set to “SAT VIDEO/RGB”.
DECODER
*: To use a decoder connected to the [L-2 IN/DECODER]
connector.
* This setting is not available in the U.K.
NOTES:
●
If you have a satellite receiver or a decoder connected to the [L-2 IN/
DECODER] connector, be sure to set “L-2 SELECT” back to
appropriate mode after editing.
●
If you are not connecting a satellite receiver or a decoder to the [L-2
IN/DECODER] connector, leave “L-2 SELECT” set to “VIDEO/RGB”.
●
When “L-2 SELECT” is set to “SAT VIDEO/RGB”, “SAT” appears on
the TV screen or front display panel instead of “L-2”.
●
If “L-1 OUTPUT” is set to “SCART S-VIDEO”, it is not possible to set
“L-2 SELECT” to “DECODER” or “SAT VIDEO/RGB”.
●
If “L-1 OUTPUT” is set to “SCART RGB”, it is not possible to set “L-2
SELECT” to “DECODER”.
●
If “L-1 OUTPUT” is set to “COMPONENT” and “L-2 SELECT” to “SAT
VIDEO/RGB” or “DECODER”, be sure to connect the [L-1 IN/OUT]
connector with a TV.
●
If “L-2 SELECT” is set to “S-VIDEO/RGB”, the monocrome signal is
output from VHS deck. Be sure to select setting other than
“S-VIDEO/RGB” when you use the VHS deck.
F-1 Input Setting
Set “F-1 INPUT” to the appropriate mode depending on the
connector ([VIDEO] or [S-VIDEO]) being used on the front panel.
1
Perform steps
1
and
2
of “L-1 Output And L-1 Input Setting”
(
墌
pg. 44).
2
Press
rt
to select “F-1 INPUT”, then press
ENTER
.
3
Press
rt
to select the
appropriate setting, then press
ENTER
.
4
Press
SET UP
to complete the
setting.
* The
boldface
settings below
indicate the settings at your
purchase.
8
F-1 INPUT
—
VIDEO
/ S-VIDEO
VIDEO
: When connecting an appliance to the [VIDEO] input
connector, set to “VIDEO”.
S-VIDEO
: When connecting an appliance to the [S-VIDEO] input
connector, set to “S-VIDEO”.
NOTE:
●
If “F-1 INPUT” is set to “S-VIDEO”, the monocrome signal is output
from VHS deck. Be sure to select “VIDEO” when you use the VHS
deck.
S-VIDEO/RGB
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
EXIT
OK
SELECT
SET UP
DVD SET UP
FUNCTION SET UP
INITIAL SET UP
VIDEO IN/OUT RECORDING SET
OTHERS
MONITOR TYPE
F-1 INPUT
L-1 INPUT
DISPLAY SET
L-1 OUTPUT
L-2 SELECT
VIDEO
VIDEO
SCART VIDEO
S-VIDEO/RGB
VIDEO/RGB
SAT VIDEO/RGB
DECODER
4:3LB
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
EXIT
OK
SELECT
SET UP
DVD SET UP
FUNCTION SET UP
INITIAL SET UP
VIDEO IN/OUT RECORDING SET
OTHERS
MONITOR TYPE
F-1 INPUT
L-1 INPUT
DISPLAY SET
L-1 OUTPUT
L-2 SELECT
VIDEO
VIDEO
SCART VIDEO
S-VIDEO
VIDEO
VIDEO/RGB
4:3LB
MV5SEK_00.book Page 45 Wednesday, August 31, 2005 7:58 PM
