background image

30

4  Permanent settings in programming mode

In the program item 

‘Machine settings 1 (4/6)’

 / 

‘Factory setting’

 you 

can reset various settings to their factory settings:

 

U

‘Machine’

 

U

All customer settings

 (apart from the ‘filter’) are reset to 

factory settings. Your IMPRESSA then switches off.

 

U

‘Products’

 

U

The settings (amount of water, aroma, temperature etc.) for 
any product can be reset 

individually

 to the factory settings. 

The corresponding double product is also reset to the fac-
tory settings at the same time.

 

U

‘All products’

 

U

The settings (amount of water, aroma, temperature etc.) for 

all products

 are reset to the factory settings.

 

U

‘Display’

 

U

All display settings are reset to the factory settings.

Example: 

Proceed as follows to reset the values for 

‘Espresso’

 to the 

factory settings.

Precondition: 

‘Please select product:’

 is displayed.

  

O

  

T

  Press the P button.

‘Maintenance status (1/6)’

  

g

  

T

  Turn the Rotary Switch until the program item 

‘Machine set-

tings 1 (4/6)’

 is displayed.

T

  Press the 

‘Factory setting’

 button.

‘Factory setting’

T

  Press the 

‘Products’

 button.

T

  Press the 

‘Espresso’

 button.

‘Espresso’

 / 

‘Reset this product to the factory setting?’

T

  Press the 

‘Next’

 button.

‘Saved’

 appears briefly on the display.

‘Factory setting’

  

O

  

T

  Press the P button to exit programming mode.

‘Please select product:’

Restore factory settings  

Summary of Contents for IMPRESSA J9 One Touch





















































Reviews: