manualshive.com logo in svg

Juniper HarvestMaster GRAINGAGE H2 STATIONARY, User Manual

Share
Download
Juniper HarvestMaster GRAINGAGE H2 STATIONARY User Manual Download Page 58

H2 Stationary GrainGage User’s Guide

                                                                                                                                                                                                      58

H2 Stationary GrainGage Calibration

8.  Tap the

 Cycle

 button 

. 

Mirus displays the moisture, voltage, bucket weight, and temperature of the sample.  

If desired, tap on the gear icon   on the right for more information about the moisture curve.

Note: Only adjust these settings if a HarvestMaster Field Service Engineer tells you to.

9.  Cycle the same sample through the GrainGage (repeat steps 7 and 8) two more times. This allows 

Mirus to average the moisture readings for each sample. 

10.  Repeat steps 7–9 for all prepared samples. Each grain sample should be cycled 3–5 times. 

11.  Calculate the moisture percentage offsets. 

The adjustment is the difference between the benchtop sensor’s moisture measurement and the 

GrainGage’s moisture measurement. 

For example, Sample One has the following moisture measurements: 

 

•

Benchtop sensor: 18%

 

•

GrainGage: 16.8% 

The adjustment would be 18% − 16.8% = +1.2%

Gear icon

Summary of Contents for HarvestMaster GRAINGAGE H2 STATIONARY
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands