background image

11

.1

4

 E

N

92

5.3.2 Adjusting the steering wheel / steering column

CAUTION!

Do not adjust the steering wheel while travelling

Individual steering wheel position

Z

The steering wheel can be height- and tilt-adjusted to suit the operator.

Adjusting the Tilt

Procedure

• Pull up on the adjusting lever (174).
• Tilt the steering wheel (175) forward or

backward as required.

• Push the adjusting lever into the centre

position.

The steering column tilt is adjusted.

Adjusting the Height

Procedure

• Push down on the adjusting lever (174). 
• Adjust the steering column (4) to the required height.
• Pull the adjusting lever (174) into the centre position.

The steering column height is adjusted.

5.3.3 Adjusting the arm rest

The height and angle of the armrest can be
adjusted with the screw (176).

Procedure

• Turn the screw clockwise - the armrest is

raised.

• Turn the screw anti-clockwise - the armrest

is lowered. 

The armrest is adjusted.

174

175

4

176

Summary of Contents for DFG 660






























































































































































































































Reviews: