Julabo MV-12 Manual Download Page 29

Page: 29 / 32

MV / MW

15.

Technical specifications

MW-Z

-4/-6/-12/-26

Working temperature range

°C

40 ... 200

25 ... 200

45 ... 200

with tap water cooling

°C

20 ... 200

Temperature stability

±0.01 °C

Temperature selection

digital

via keypad

indication on MULTI-DISPLAY (LED)

remote control via personal computer

indication on monitor

Temperature indication

MULTI-DISPLAY (LED)

Resolution

0.1 °C

ATC -

Absolute Temperature Calibration

±3 °C

Temperature control

PID

Working temperature sensor

Pt 1000

Safety temperature sensor

Pt 1000

Heater wattage

2000 W (at 230 V)
or 1000 W (at 115V)

Pressure pump

pressure, max.

at 0 liter

340 mbar

discharge, max.

at 0 bar

15l/min

20 l/min

Suction pump:
suction, max.

at 0 liter

220 mbar

discharge, max.

at 0 bar

14 l/min

Electrical connections
Alarm output

24-0 V DC / max. 25 mA

Computer interface

RS232C

Ambient temperature

5 °C ... 40 °C

Mains power connection ±10 %

230 V / 50 Hz
or 115 V / 60 Hz

Total power consumption

(at 230 V) W

2100

2150

(at 115 V) W

1100

1150

All measurements have been carried out at:
rated voltage and frequency

ambient temperature: 20 °C

Technical changes without prior notification reserved.

Summary of Contents for MV-12

































Search results

Summary of Contents for MV-12

Reviews:

Julabo MV-12, Manual, Page: 29 / 32

Search results

Summary of Contents for MV-12

Reviews: