manualshive.com logo in svg

Julabo MV-12, Manual, Page: 24 / 32

Share
Download
Julabo MV-12 Manual Download Page 24

Remote control

24

12.

Remote control

12.1. Setup for remote control

RS232C

Interface parameters for the circulator are adjusted at
configuration level.
Enter or exit the configuration level by pressing the left arrow

 and enter 

 at the same time.

The menu item "

Atc

" appears on the MULTI-DISPLAY

(LED). After pressing the cursor key 

, the second menu

item "REMOTE" is indicated. The interface parameters
cannot be adjusted unless the display reads "r 0".

Adjusting interface parameters:

Example: changing the baud rate.

 Using the arrow keys 

 move the cursor to the

desired menu. The actual parameter is displayed (example:
"br 24" = 2400 bauds).

 With the up and down arrows 

 change the

number to the desired parameter (example: 4800 bauds).
The changed numerals are blinking.

 The new parameter is stored in memory by pressing enter

.

Adjustable interface parameters

REMOTE

0 = keypad control mode
1 = remote control mode via RS232C

BAUDRATE

12 = 1200 bauds
24 = 2400 bauds
48 = 4800 bauds *
96 = 9600 bauds

PARITY

0 = no parity
1 = odd parity
2 = even parity *

HANDSHAKE

0 = Protocol Xon/Xoff

(software handshake)

1 = Protokol RTS/CTS

(hardware handshake) *

Data bits: 7; Stop bits: 1*

(* Factory setting )

Summary of Contents for MV-12

































Reviews:

No comments