manualshive.com logo in svg

Julabo MV-12, Manual, Page: 13 / 32

Share
Download
Julabo MV-12 Manual Download Page 13

MV / MW

13

6.

Operating procedures

6.1.

Power connection

Connect the unit only to a grounded mains power socket!
We disclaim all liability for damage caused by incorrect line
voltages!

Check to make sure that the line voltage matches the
supply voltage specified on the identification plate.
Deviations of ±10 % are permissible.

6.2.

Switching on / Start - Stop

Switching on:
Turn on the mains power switch.
The unit performs a self-test. All segments of the 4-digit
MULTI-DISPLAY (LED) and all indicator lights will
illuminate.
Then the software version (example: n 1.2) appears.
The display "

OFF

" or "

r

 

OFF

"

 indicates the unit is

ready to operate (standby mode).
The circulator enters the operating mode activated
before switching the circulator off:

keypad control mode 

(manual operation) or

remote control mode 

(operation via personal

computer).

Start:

 Press the start/stop key.

- The MULTI-DISPLAY (LED) indicates the actual

bath temperature. (example: 21.0 °C)

- An illuminated indicator light in the "T1" or "T2"

key indicates the activated working temperature.

Stop:

 Press the start/stop key.

The MULTI-DISPLAY (LED) indicates the message
"OFF".

Summary of Contents for MV-12

































Reviews:

No comments