JRC JSS-2150 -, Instruction Manual

Page: 56 / 248

Names and Functions
2-4
2.2.2 Operating display
(1) General
After setting the frequency, pressing PTT key in TEL mode, sending/receiving messages in
DSC/TLX mode, and things like that, the controller shows the operating display as follows.
1. Indicates the MMSI and the latest position
and that time.
2. Indicates an focused screen with sign
and thick-frame, i.e. the operating display
is divided into three screens as below,
where the focused screen can be moved
using the
FUNC key for clockwise.
3. Indicates the transceiver setting screen
similar to the status display. Icons on this
area are as follows.
 Scanning :
 Not tuned yet :
 Tx pwr reduction (low) :
 Turned the PA ON :
 Attenuation (dB) :
 AGC (
Fast/ Slow)
:

Noise reduction (NR1/NR2/BC)
:
4. Indicates the S meter (or TX meter), and
watchkeeping receiver monitoring
frequencies mentioned above.
5. Indicates the existing procedures. If the
procedure is under operation (active), A
mark is added in the box frame. Further, if
other procedures on hold exist, they are
indicated in the other box frames and are
selectable to operate at any time. And
while this screen is focused, the turning
dial animation is shown as below.
6. Indicates the content and the handling
menus of the procedure located at the top
of the procedure list screen.
During operating an active procedure, any functions such like the DSC automatic
acknowledgement become invalid to avoid the ongoing communication interruption.
TEL
ON
I D 4 3 1 0 0 1 2 3 4 2 3 : 5 9 ( U T C )
P o s 8 9 ﾟ 5 9 . 0 1 2 3 ' N
1 7 9 ﾟ 5 9 . 6 7 8 9 ' E @ 2 3 : 5 9
S
IG
12 -S N2
RX
13077.00
kHz
TX
12230.00
kHz
D
UP
W
KR
2 4 6 8 12 16
A COMM
C o m m u n i c a t i n g o n
T E L R x : 1 3 0 7 7 . 0 0 / T x : 1 2 2 3 0 . 0 0 k H z
T i p ) U s e F U N C t o c h a n g e o p a r e a .
[ H L D ] [ E N D ]
COMM
S
AF
D
ST
U
RG
G
PS
TEL
I D 4 3 1 0 0 1 2 3 4 2 3 : 5 9 ( U T C )
P o s 8 9 ﾟ 5 9 . 0 1 2 3 ' N
1 7 9 ﾟ 5 9 . 6 7 8 9 ' E @ 2 3 : 5 9
S
IG
D
UP
W
KR
2 4 6 8 12 16
A COMM
C o m m u n i c a t i n g o n
T E L R x : 1 3 0 7 7 . 0 0 / T x : 1 2 2 3 0 . 0 0 k H z
T i p ) U s e F U N C t o c h a n g e o p a r e a .
[ H L D ] [ E N D ]
COMM
G PS
L ON T 12 -S N2
RX
13077.00
kHz
TX
12230.00
kHz
TEL
L ON T
I D 4 3 1 0 0 1 2 3 4 2 3 : 5 9 ( U T C )
P o s 8 9 ﾟ 5 9 . 0 1 2 3 ' N
1 7 9 ﾟ 5 9 . 6 7 8 9 ' E @ 2 3 : 5 9
S
IG
12 -S N2
RX
13077.00
kHz
TX
12230.00
kHz
D
UP
W
KR
2 4 6 8 12 16
A COMM
C o m m u n i c a t i n g o n
T E L R x : 1 3 0 7 7 . 0 0 / T x : 1 2 2 3 0 . 0 0 k H z
T i p ) U s e F U N C t o c h a n g e o p a r e a .
[ H L D ] [ E N D ]
COMM
G
PS
3
1
2
5
6
Note
4
Transceiver
setting
Procedure
list
Message/event
control