JRC JLR-21 Instruction Manual Download Page 60

Page: 60 / 164

4-4

SOG Screen

COG Screen

4.1.3 Navigation Screen

The latitude and longitude of the ship's position are displayed.

Latitude and longitude displays (3 decimals or 4 decimals display)
can be cycled between using the and keys.

SOG: Speed over

ground

Bow heading (HDG)

COG: Course over

ground

RAIM information:
The following information is displayed in the
configured accuracy level. (Refer to 5.3.3. GPS
Configuration (GPS).)
RAIM ON: Displays the configured accuracy

level (10m 30m 50m 100m)

RAIM OFF: RAIM OFF
No failed satellite: SAFE
Unable to RAIM: CAUTION
Occurrence of a failed satellite: UNSAFE SATID XX

(XX is satellite No.)

"-": Less than 1 knot.

COG "-": Less than 1 knot.

Summary of Contents for JLR-21





































































































































































Search results

Summary of Contents for JLR-21

Reviews:

Related manuals for JLR-21

Brands by name

Popular brands

JRC JLR-21, Instruction Manual

Search results

Summary of Contents for JLR-21

Reviews:

Related manuals for JLR-21

Brands by name

Popular brands