JRC JLR-21 Instruction Manual Download Page 118 | Manualshive

Page: 118 / 164

background image

6-6

6.3 Troubleshooting

6.3.1 Troubleshooting

WARNING

Do not perform internal inspections or modifications of the equipment.
Inspection or modification by unauthorized personnel may result in fire, electric
shock, or equipment failure. Please consult with JRC or an affiliate to perform
internal inspections or repair.

The following is reference information concerning identification of problems.

Problem Behavior

Possible Causes

Troubleshooting Measures

The power does not turn on
when the power switch is
pressed.

Power is not being supplied
by the ship junction box.

Check the cabling from the junction
box.

Power is not being supplied
by the power supply
equipment (option).

Check the power supply unit cabling.

The fuse connected to the
power cable has blown.

If there are no problems in the cabling,
replace the fuse.

The power supply equipment
(option) fuse has blown.

If there are no problems in the cabling,
replace the fuse.

The display unit switch is
broken.

Consult with JRC or an affiliate

.

The LCD display does not
display anything.

The LCD display is broken.

Consult with JRC or an affiliate.

The display does not light
up.

The buzzer sound. Is not
generated

The buzzer is broken.

Consult with JRC or an affiliate.

The click does not sound.

The key press sound is
turned off.

Refer to 5.3.1.3 for setting the key
press sound.

There is no reception.
(from sensor)

The sensor connection cable
is cut.

Check the connection cable.

The sensor is broken.

Consult with JRC or an affiliate.

There is no reception.
(from external devices)

The polarity of the serial
cable is incorrect.

Check the polarity of the cable.

The interface does not
match.

Check the interface.

An unsupported sentence
has been entered.

Check the entered commands and
version.

There is no transmission.
(to external devices)

Output settings have not
been configured.

Refer to 5.3.7 for setting the key press
sound.

The configured channel is
incorrect.

Refer to 5.3.7 for setting the key press
sound.

The DISP-DPU or
connector board is broken.

Consult with JRC or an affiliate.

«
...
116
117
118
119
120
...
»

Summary of Contents for JLR-21





































































































































































Reviews:

No comments

Related manuals for JLR-21

Brand: Garmin Pages: 2

FUSION Apollo MS-WB670

Brand: Garmin Pages: 44

Brand: Magnavox Pages: 78

Wave SoundTouch IV series

Brand: Bose Pages: 32

Brand: Magnavox Pages: 25

UNI_NIGHTVISION_01

Brand: UNIPRODO Pages: 9

Brand: Kitsound Pages: 10

Brand: LG Pages: 20

Brand: LG Pages: 56

Brand: LG Pages: 34

Brand: LG Pages: 200

Brand: Samsung Pages: 42

Brand: BoomToneDJ Pages: 32

Brand: DTech Pages: 7

Brand: Denver Pages: 9

Brand: Denver Pages: 18

Brand: Denver Pages: 84

Brand: Denver Pages: 97

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands