JRC JLR-21 Instruction Manual Download Page 81 | Manualshive

Page: 81 / 164

background image

5-17

5.3.1.6 Decimal Display Size Setting (DECIMAL DISP SIZE)

The display size of decimals on the screen assigned to the DISP key (refer to 4.1 Display Screen) can
be selected.

LARGE: The display size of decimal numbers is large.    Ex.
SMALL: The display size of decimal numbers is small.    Ex.

Applicable screens are Compass Screens A to F, Bow Heading Screen, Navigation Screen, Turn Rate
Screen, and Water Speed/Ground Speed Screen.

5.3.1.7 Current Position Display Digit Setting on Compass Screens C/D (COMP-C/D POSITION

DIGIT)

The number of digits for displaying the current position on the Compass screens C/D can be selected.

3: The current position is displayed with 3 decimals. Ex.

4: The current position is displayed with 4 decimals. Ex.

«
...
79
80
81
82
83
...
»

Summary of Contents for JLR-21





































































































































































Reviews:

No comments

Related manuals for JLR-21

Brand: Emerson Pages: 22

Brand: Emerson Pages: 22

Brand: Emerson Pages: 27

Brand: Emerson Pages: 30

Brand: Emerson Pages: 27

Brand: Emerson Pages: 40

Brand: Emerson Pages: 44

Brand: Emerson Pages: 44

Brand: Louroe Electronics Pages: 8

Brand: Sennheiser Pages: 30

Brand: Venturer Pages: 10

Brand: Aiwa Pages: 27

Brand: Raisecom Pages: 62

Brand: Aiwa Pages: 58

Brand: Auxdio Pages: 35

Brand: MuxLab Pages: 2

Brand: Audizio Pages: 36

Brand: Palsonic Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands