40
ES
La silla de automóvil dispone de 3 posiciones de reclinación, sea que se encuentre en el sentido de
la marcha o que se encuentre en sentido contrario a la marcha.
Para reclinar la silla actuar sobre la manija de regulación colocada debajo del asiento en la parte
frontal y regularla en la posición deseada, hacia adelante o hacia atrás.
Una vez lograda la posición, liberar la manija. Un “click” indicará que se ha efectuado la reclinación.
NOTA:
asegurarse siempre que la silla esté ajustada en una de las 3 posiciones de reclinación y
jamás se encuentre en posiciones intermedias.
INSTALACION DE LA BASE DE LA SILLA
Press ISOFIX release button to make ISOFIX connectors
come out of the base.
Push the ISOFIX base(A3),until ISOFIX connectors are
completely locked with the connection device of car.
“CLICK”sound indicates that ISOFIX connector has been
locked(A4,A5).
When the end of ISOFIX connector turns to green,it is
locked.Shown in red, it is not locked(A4).
Adjust the length of the leg to make sure that the leg can
touch the ground of the car very steadily(A5).
12. Instructions of uninstalling the base
Press ISOFIX unlock button to release the ISOFIX
(B1,B2).
If you don’t need to use car seat,press ISOFIX adjusting button.At the same
time,another hand push ISOFIX,according to the direction of the arrow to push
can shrink ISOFIX connector(B3).
base
10.Remove the buckle and car seat pad
11. Instructions of installing the base
STEP 1:
Release the buckle(fig.1),release the shoulder belt as long as you can.
STEP 2:
(fig.2)
STEP 3:
Take out the buckle from the pad(fig.3).
Please keep the buckle and crotch pad as well.
Please adjust the seat to the biggest angle,you will see the end bracket
under the car seat.Then you can pull out the harness from the solt which under
the car seat
.
Note:
Pay attention:
if not necessary,please do not disassemble the shoulder belt.
STEP 5:
Pull all direction to take out the cover(fig.6)
★
The above steps in turn, that is the cloth cover installation method
STEP 4:
comfortable cushion,chest pad and buckle connectors(fig.5).
Slide both of the harness off the harness connector(fig.4),and take off
the
9
10
1
2
3
4
5
6
A2
A5
A6
Note:Leg not hanging in the air or other items can be used to support.At the same
time to ensure that the leg is no higher that the safety seat.Check whether leg
shows green(A6).
B2
B3
CLICK
A4
√
×
CLICK
UNLOCK
B1
PRESS
A1
A3
Press ISOFIX release button to make ISOFIX connectors
come out of the base.
Push the ISOFIX base(A3),until ISOFIX connectors are
completely locked with the connection device of car.
“CLICK”sound indicates that ISOFIX connector has been
locked(A4,A5).
When the end of ISOFIX connector turns to green,it is
locked.Shown in red, it is not locked(A4).
Adjust the length of the leg to make sure that the leg can
touch the ground of the car very steadily(A5).
12. Instructions of uninstalling the base
Press ISOFIX unlock button to release the ISOFIX
(B1,B2).
If you don’t need to use car seat,press ISOFIX adjusting button.At the same
time,another hand push ISOFIX,according to the direction of the arrow to push
can shrink ISOFIX connector(B3).
base
10.Remove the buckle and car seat pad
11. Instructions of installing the base
STEP 1:
Release the buckle(fig.1),release the shoulder belt as long as you can.
STEP 2:
(fig.2)
STEP 3:
Take out the buckle from the pad(fig.3).
Please keep the buckle and crotch pad as well.
Please adjust the seat to the biggest angle,you will see the end bracket
under the car seat.Then you can pull out the harness from the solt which under
the car seat
.
Note:
Pay attention:
if not necessary,please do not disassemble the shoulder belt.
STEP 5:
Pull all direction to take out the cover(fig.6)
★
The above steps in turn, that is the cloth cover installation method
STEP 4:
comfortable cushion,chest pad and buckle connectors(fig.5).
Slide both of the harness off the harness connector(fig.4),and take off
the
9
10
1
2
3
4
5
6
A2
A5
A6
Note:Leg not hanging in the air or other items can be used to support.At the same
time to ensure that the leg is no higher that the safety seat.Check whether leg
shows green(A6).
B2
B3
CLICK
A4
√
×
CLICK
UNLOCK
B1
PRESS
A1
A3
Presionar el botón de desenganche para liberar la salida de los conectores
ISOFIX de la base (fig.A1).
Con los conectores ISOFIX completamente extraídos, fijar la base a
los enganches ISOFIX del asiento del vehículo. Un “click” indicará el
correspondiente enganche y un indicador de color verde aparecerá sobre los
lados de los conectores ISOFIX de la base (fig.A4).
Regular la altura de la barra de apoyo presionando el botón de regulación
colocado en la barra.
La barra debe apoyar firmemente sobre el fondo del vehículo; un indicador de color verde colocado
en la base de la barra señalarà el correcto apoyo (fig.A5/A6).
Verificar que la barra de apoyo esté bloqueada, permanezca en posición firme y no se mueva hacia
arriba o hacia abajo.
Summary of Contents for JL-1048 SECURFIX BEEP
