Joyello JL-1048 SECURFIX BEEP, User Manual

Page: 26 / 68

26
GB
This child seat has 3 reclined positions whether positioned forward-facing or rear-facing.
To recline the child seat, press the adjuster button located under the front of the child seat and
position it as required, forward or back.
Once you have reached the required position, release the recliner mechanism’s adjuster button. The
child seat will click when it locks into position.
NOTE: always ensure that the child seat is locked in one of the three reclined positions and is not
left in an intermediate position.
INSTALLING THE SEAT BASE
Press ISOFIX release button to make ISOFIX connectors
come out of the base.
Push the ISOFIX base(A3),until ISOFIX connectors are
completely locked with the connection device of car.
“CLICK”sound indicates that ISOFIX connector has been
locked(A4,A5).
When the end of ISOFIX connector turns to green,it is
locked.Shown in red, it is not locked(A4).
Adjust the length of the leg to make sure that the leg can
touch the ground of the car very steadily(A5).
12. Instructions of uninstalling the base
Press ISOFIX unlock button to release the ISOFIX (B1,B2).
If you don’t need to use car seat,press ISOFIX adjusting button.At the same
time,another hand push ISOFIX,according to the direction of the arrow to push
can shrink ISOFIX connector(B3).
base
10.Remove the buckle and car seat pad
11. Instructions of installing the base
STEP 1: Release the buckle(fig.1),release the shoulder belt as long as you can.
STEP 2:
(fig.2)
STEP 3: Take out the buckle from the pad(fig.3).
Please keep the buckle and crotch pad as well.
Please adjust the seat to the biggest angle,you will see the end bracket
under the car seat.Then you can pull out the harness from the solt which under
the car seat .
Note:
Pay attention: if not necessary,please do not disassemble the shoulder belt.
STEP 5: Pull all direction to take out the cover(fig.6)
★
The above steps in turn, that is the cloth cover installation method
STEP 4:
comfortable cushion,chest pad and buckle connectors(fig.5).
Slide both of the harness off the harness connector(fig.4),and take off
the
9 10
1 2 3
4 5 6
A2
A5 A6
Note:Leg not hanging in the air or other items can be used to support.At the same
time to ensure that the leg is no higher that the safety seat.Check whether leg
shows green(A6).
B2 B3
CLICK
A4
√
×
CLICK
UNLOCK
B1
PRESS
A1
A3
Press ISOFIX release button to make ISOFIX connectors
come out of the base.
Push the ISOFIX base(A3),until ISOFIX connectors are
completely locked with the connection device of car.
“CLICK”sound indicates that ISOFIX connector has been
locked(A4,A5).
When the end of ISOFIX connector turns to green,it is
locked.Shown in red, it is not locked(A4).
Adjust the length of the leg to make sure that the leg can
touch the ground of the car very steadily(A5).
12. Instructions of uninstalling the base
Press ISOFIX unlock button to release the ISOFIX (B1,B2).
If you don’t need to use car seat,press ISOFIX adjusting button.At the same
time,another hand push ISOFIX,according to the direction of the arrow to push
can shrink ISOFIX connector(B3).
base
10.Remove the buckle and car seat pad
11. Instructions of installing the base
STEP 1: Release the buckle(fig.1),release the shoulder belt as long as you can.
STEP 2:
(fig.2)
STEP 3: Take out the buckle from the pad(fig.3).
Please keep the buckle and crotch pad as well.
Please adjust the seat to the biggest angle,you will see the end bracket
under the car seat.Then you can pull out the harness from the solt which under
the car seat .
Note:
Pay attention: if not necessary,please do not disassemble the shoulder belt.
STEP 5:
Pull all direction to take out the cover(fig.6)
★
The above steps in turn, that is the cloth cover installation method
STEP 4:
comfortable cushion,chest pad and buckle connectors(fig.5).
Slide both of the harness off the harness connector(fig.4),and take off
the
9 10
1 2 3
4 5 6
A2
A5 A6
Note:Leg not hanging in the air or other items can be used to support.At the same
time to ensure that the leg is no higher that the safety seat.Check whether leg
shows green(A6).
B2 B3
CLICK
A4
√
×
CLICK
UNLOCK
B1
PRESS
A1
A3
Press the release button to extend the ISOFIX connector arms out from the
base (fig. A1).
When the ISOFIX connector arms are completely extended, attach the base
to the ISOFIX anchor points in the vehicle’s seat. A “click” signals that the
seat is attached and a green indicator displays on each of the base’s ISOFIX
connector arms (fig.A4).
Adjust the length of the support leg by pressing the adjuster button located
on its shaft.
The leg should sit solidly on the floor of the vehicle. A green indicator located on the leg’s shaft
signals that it is correctly fitted (fig.A5/A6).
Check that the support leg is locked, stays in position and cannot move up or down.