27
installaton guide
www.jouleuk.co.uk
4.8.4 « FAN » - FANSPEED
The fan can be used at two speeds
Switching on the « FAN » function
• Select « FAN» function and press « OK ». The display shows “SP1”.
• Press«+»or«-»todefinethefanspeed:
– « SP1 » : fan speed 1 (low air volume)
– « SP2 » : fan speed 2 (high air volume)
• Press «OK».
24
ENG
Installation and user manual
4.8.4 « FAN » - FANSPEED
The fan can be used at two speeds
Switching on the « FAN » function
•
Select « FAN» function and press « OK ». The display shows
“SP1”.
•
Press « + » or « - » to define the fan speed:
–
« SP1 » : fan speed 1 (low air volume)
–
« SP2 » : fan speed 2 (high air volume)
•
Press «OK».
4.8.5 « DUCT » - USE OF DUCTS
Switching on the « Duct » function
•
Select « Duct » function and press « OK ». The display shows “dOFF”.
•
Press « + » or « - » to define the use of ducts:
–
« dOFF » : installation without ducts
–
« dON » : installation with ducts
•
Press «OK».
4.8.6 “PURG” - DRAIN
The “Purg” function can be used to drain air from the system.
Switching on the “Purg” function.
•
Call up the “Purg” function and press “OK”. The pump is switched on.
The display indicates the time remaining until the draining procedure is
complete (in minutes). After 5 minutes, the appliance reverts to the previously
selected operating mode.
4.8.7 “FSET” - DEFAULT SETTINGS
The “Fset” function can be used to restore the default settings.
Switching on the “Fset” function
•
Call up the “Fset” function and press “OK”. The display shows “Fset”.
•
Press “OK”. After 10 seconds, the default settings are restored
4.8.5 « DUCT » - USE OF DUCTS
Switching on the « Duct » function
• Select « Duct » function and press « OK ». The display shows
“dOFF” .
• Press«+»or«-»todefinetheuseofducts:
– « dOFF » : installation without ducts
– « dON » : installation with ducts
• Press «OK».
4.8.6 “PURG” - DRAIN
The “Purg” function can be used to drain air from the system . Switch-
ing on the “Purg” function .
• Call up the “Purg” function and press “OK”. The pump is switched on.
The display indicates the time remaining until the draining procedure
is complete (in minutes). After 5 minutes, the appliance reverts to the
previously selected operating mode .
4.8.7 “FSET” - DEFAULT SETTINGS
The “Fset” function can be used to restore the default settings .
Switching on the “Fset” function
• Call up the “Fset” function and press “OK”. The display shows “Fset”.
• Press “OK”. After 10 seconds, the default settings are restored.
24
ENG
Installation and user manual
4.8.4 « FAN » - FANSPEED
The fan can be used at two speeds
Switching on the « FAN » function
•
Select « FAN» function and press « OK ». The display shows
“SP1”.
•
Press « + » or « - » to define the fan speed:
–
« SP1 » : fan speed 1 (low air volume)
–
« SP2 » : fan speed 2 (high air volume)
•
Press «OK».
4.8.5 « DUCT » - USE OF DUCTS
Switching on the « Duct » function
•
Select « Duct » function and press « OK ». The display shows “dOFF”.
•
Press « + » or « - » to define the use of ducts:
–
« dOFF » : installation without ducts
–
« dON » : installation with ducts
•
Press «OK».
4.8.6 “PURG” - DRAIN
The “Purg” function can be used to drain air from the system.
Switching on the “Purg” function.
•
Call up the “Purg” function and press “OK”. The pump is switched on.
The display indicates the time remaining until the draining procedure is
complete (in minutes). After 5 minutes, the appliance reverts to the previously
selected operating mode.
4.8.7 “FSET” - DEFAULT SETTINGS
The “Fset” function can be used to restore the default settings.
Switching on the “Fset” function
•
Call up the “Fset” function and press “OK”. The display shows “Fset”.
•
Press “OK”. After 10 seconds, the default settings are restored
24
ENG
Installation and user manual
4.8.4 « FAN » - FANSPEED
The fan can be used at two speeds
Switching on the « FAN » function
•
Select « FAN» function and press « OK ». The display shows
“SP1”.
•
Press « + » or « - » to define the fan speed:
–
« SP1 » : fan speed 1 (low air volume)
–
« SP2 » : fan speed 2 (high air volume)
•
Press «OK».
4.8.5 « DUCT » - USE OF DUCTS
Switching on the « Duct » function
•
Select « Duct » function and press « OK ». The display shows “dOFF”.
•
Press « + » or « - » to define the use of ducts:
–
« dOFF » : installation without ducts
–
« dON » : installation with ducts
•
Press «OK».
4.8.6 “PURG” - DRAIN
The “Purg” function can be used to drain air from the system.
Switching on the “Purg” function.
•
Call up the “Purg” function and press “OK”. The pump is switched on.
The display indicates the time remaining until the draining procedure is
complete (in minutes). After 5 minutes, the appliance reverts to the previously
selected operating mode.
4.8.7 “FSET” - DEFAULT SETTINGS
The “Fset” function can be used to restore the default settings.
Switching on the “Fset” function
•
Call up the “Fset” function and press “OK”. The display shows “Fset”.
•
Press “OK”. After 10 seconds, the default settings are restored
24
ENG
Installation and user manual
4.8.4 « FAN » - FANSPEED
The fan can be used at two speeds
Switching on the « FAN » function
•
Select « FAN» function and press « OK ». The display shows
“SP1”.
•
Press « + » or « - » to define the fan speed:
–
« SP1 » : fan speed 1 (low air volume)
–
« SP2 » : fan speed 2 (high air volume)
•
Press «OK».
4.8.5 « DUCT » - USE OF DUCTS
Switching on the « Duct » function
•
Select « Duct » function and press « OK ». The display shows “dOFF”.
•
Press « + » or « - » to define the use of ducts:
–
« dOFF » : installation without ducts
–
« dON » : installation with ducts
•
Press «OK».
4.8.6 “PURG” - DRAIN
The “Purg” function can be used to drain air from the system.
Switching on the “Purg” function.
•
Call up the “Purg” function and press “OK”. The pump is switched on.
The display indicates the time remaining until the draining procedure is
complete (in minutes). After 5 minutes, the appliance reverts to the previously
selected operating mode.
4.8.7 “FSET” - DEFAULT SETTINGS
The “Fset” function can be used to restore the default settings.
Switching on the “Fset” function
•
Call up the “Fset” function and press “OK”. The display shows “Fset”.
•
Press “OK”. After 10 seconds, the default settings are restored
