background image

11

•  The  device  must  be  installed  in  strict  accordance  with  the  instructions  contained  in  this 

manual.

•  Comply with the laws in force in the country in which the device is installed, regarding the use 

and disposal of the packaging and products used for cleaning and servicing the device; you 
should also observe the recommendations given by the manufacturer of such products.

• 

before switching the device on check the integrity of the various components and of the 
electrical mains to which it is connected, making sure that it is fitted with a circuit breaker 
upstream of the power line as shown in this manual.

•  Never insert objects of any kind into the device, as coming into contact with live parts or 

electrical terminals may cause fires or electric shocks.

•  Do not service or clean the device without first unplugging it from the mains.
•  Worn or damaged parts must only be repaired or replaced by qualified staff and by following 

the instructions given in this manual.

•  The spare parts must be approved by the Manufacturer.
•  In the event of decommissioning or disposing of the device, follow the anti-pollution regulations 

set out by the country in which the device is installed.

•  Do not pour water or any kind of liquids on the device.
•  Place the device so that the power cable cannot be stepped on.

6 - InsTallaTIon anD coMMIssIonInG

aTTenTIon! before carrying out any operation on the devices read all the 

instructions in this manual carefully.

6.1  safeTY sTanDaRDs 

The Manufacturer disclaims any liability for failure to comply with the safety and 
prevention standards as described below.
The Manufacturer also disclaims any liability for damage caused by improper use 

of sanitisers and/or alterations carried out without prior authorisation.

Definitions:

UseR: 

Person, organisation or 
company who or which 
has purchased or 
rented the device and 
is going to use it for the 
intended purposes.

UseR/oPeRaToR: 
Individual who has been 
authorised by the user to 
operate the device.

QUalIfIeD sTaff:
Individuals who have completed a 
specific course and are therefore 
able to recognise the hazards 
arising from the use of this device 
and are able to prevent them.

Summary of Contents for 70WHITECUBE





























Reviews: