Joab EcoDrive Operation And Maintenance Manual Download Page 7 | Manualshive

Page: 7 / 73

Joab EcoDrive Operation And Maintenance Manual Download Page 7

vii

Introduction

This manual explains how to operate and maintain your EcoDrive Hook-Lift. It contains import-
ant information for your own safety and the surrounding environment.

JOAB’s products are characterised by a high level of safety, reliability, and long service-life. To
get the best out of your EcoDrive Hook-Lift, we recommend reading this manual carefully.

This manual also contains information regarding fault tracing, lubrication, and servicing of your
EcoDrive Hook-Lift. This manual is based on the original mounted equipment only. Refer to the
relevant supplier’s manuals for all other optional or auxiliary equipment.

JOAB takes no responsibility for consequences that occur due to work carried out by non-pro-
fessionals.

After receiving the EcoDrive Hook-Lift, ensure that it is in proper working order. If it is not, con-
tact JOAB, your dealer, or other supplier.

The specifications, constructions, and illustrations found in this manual are not binding.
JOAB AB retains the right to make changes without prior notice.

For all EcoDrive Hook-Lifts sold in Sweden, the general delivery regulations apply.

A training CD is included with certain deliveries. This comprehensively describes how to use
JOAB’s products, such as EcoDrive Hook-Lifts, lift dumpers, and the Hookmaster.

Always bare in mind that it is the operator that is responsible for handling the EcoDrive Hook-
Lift.

© JOAB AB

EcoDrive manual: 13300 Edition 1 | 2019-01-31

«
...
5
6
7
8
9
...
»

Summary of Contents for EcoDrive










































































Reviews:

No comments