background image

Maintenance of the lubrication points on the hook-lift should normally follow the vehicle's main-
tenance scheme for lubrication. However, the hook-lift's lubrication points must be maintained
after every 75 hours of operation.

If the vehicle is equipped with a central lubrication system, it is important to ensure that it func-
tions correctly after every 75 hours. And in addition, any lubrication points that are not included
in the central system are maintained.

Use grease type: NLGI 0 or thicker when a central greasing system is employed. Bearings with
a high load, such as those in the rollers, must use a higher grease viscosity than normal.

Do not apply grease or oil onto the guide rails.

Service of the Hook-Lift

During normal operation, it is recommended
that the oil is changed as follows:

l

Mineral oil – once every two years

l

Green oil – once every year

JOAB recommends that the oil is changed dur-
ing the autumn period.

If green oil is used for the system, always use
the same type of oil and manufacturer of the oil.

The oil-filter must be changed after the first fifty
hours of operation, then every year after that.

The air-filter should be replaced at least once every two years, or more often, as required.

Service-Reminder Sticker

A JOAB service sticker is placed on the inside of the drivers door to
indicate when the hook-lift is due for its next service. In the example
shown opposite, the numbers around the outside represent the
months January to December.

As the month numbered 1 (January) is missing from the sticker, this
indicates that the next service is due during the month of January.
Make sure that the hook-lift is serviced in accordance with the sticker.

Service Packets and Warranty

Service packets can be ordered from JOAB using the information provided below. Always have
the information provided on the hook-lift's manufacture plate ready before making contact.
Refer to

"Manufacture Plate", on page 4

.

54

Service and Maintenance | Service of the Hook-Lift

EcoDrive manual: 13300 Edition 1 | 2019-01-31

Summary of Contents for EcoDrive










































































Reviews: