Joab EcoDrive Operation And Maintenance Manual Download Page 43 | Manualshive

Page: 43 / 73

background image

7.

Operate the tip function so that the hook-
post is in position ready for collecting the
body.

8.

LA models only:
Before reversing towards the body's lifting-
bracket, make sure that the safety-hook on
the hook-post is open.

9.

Reverse the vehicle towards the body aiming the hook-post at the centre of the body’s lifting
bracket. Make sure to reverse straight towards the body. If the vehicle is not reversed
straight towards the body, there is a risk of missing the rollers when loading the body.

10.

Operate the extending-section as required and engage the hook-post with the body's lift-
ing-bracket.

11.

Inspect and verify that the hook is correctly engaged with the body's lifting bracket.

12.

Use the tip function and lift the body. If the load is heavy or the body’s rollers are stuck in the
underlying surface, reverse carefully at the same time as lifting.

LA Models only:

Use the folding-hook-post only when it is necessary, for example when a low pulling angle
is required.

35

Loading a Body |

EcoDrive manual: 13300 Edition 1 | 2019-01-31

«
...
41
42
43
44
45
...
»

Summary of Contents for EcoDrive










































































Reviews:

No comments

Related manuals for EcoDrive

Brand: JBM Pages: 35

Brand: Tanco Autowrap Pages: 3

Picomig 305 D2 puls

Brand: EWM Pages: 84

Brand: jablotron Pages: 3

Brand: Mortuary Lift Pages: 6

Vision BT-A02 RF

Brand: Watts Pages: 19

Brand: Nußbaum Hebetechnik Pages: 32

AIR VANTAGE 500 CUMMINS

Brand: Lincoln Electric Pages: 51

Brand: salmson Pages: 20

Brand: Miller Pages: 32

Brand: Zepro Pages: 6

2200 Traditional Series

Brand: Zephir Pages: 2

Enado Mini ENA-MINI-010

Brand: Wyrestorm Pages: 2

Brand: BHM Medical Pages: 29

Brand: NI Pages: 28

Brand: Lincoln Electric Pages: 32

Brand: Sherman Pages: 14

Brand: Aircalo Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands