Joab EcoDrive LA Operation And Maintenance Manual Download Page 77 | Manualshive

Page: 77 / 89

background image

69

Safety Warnings

The EcoDrive Hook-Lift has a number of safety labels attached to it, as shown below. It is
important to read and adhere to these warnings. Failure to do so can lead to serious injury or
damage to equipment.

Make sure that the labels are in good condition. If necessary, new safety labels can be ordered
from JOAB.

Safe Working Distance

Make sure that there are no unauthorised persons in close prox-
imity of the EcoDrive Hook-Lift's working area. The risk zone is
8 metres in all directions of the EcoDrive Hook-Lift and body.

Working on the Hook-Lift

Never work under a hook-lift without the use of the tip-supports.
Make sure that the body is removed from the hook-lift and that
the tip-supports are mounted correctly so that they support the
hook-lift, before carrying out any work.

Refer also to

"Working on the Hook-Lift", on page 66

Park the Hook-Lift before driving the Vehicle

Make sure the hook lift is parked before driving the vehicle. Fail-
ure to do so can lead to serious injury or damage. There is a ser-
ious risk that the hook will make contact with the environment if
it is not parked.

Risk of Slipping

Be aware when operating the hook-lift that there may be a risk of slipping, that
could lead to injury.

Suspended Loads

Do not stand or walk underneath a suspended load. If a suspended load
breaks free it can lead to serious injury or death.

EcoDrive 2.0 manual: 1021970 Edition 1 | 2022-02-04

«
...
75
76
77
78
79
...
»

Summary of Contents for EcoDrive LA


























































































Reviews:

No comments

Related manuals for EcoDrive LA

Brand: Parkside Pages: 54

weldmatic 350i CP139-2

Brand: WIA Pages: 28

Brand: Lincoln Pages: 40

SystemRoMedic EvaDrive450

Brand: Handicare Pages: 37

DHI-IPMECD-3021 Series

Brand: Dahua Technology Pages: 28

NVL Vista 05 Series

Brand: Braun Pages: 30

Brand: DAAB Pages: 24

Brand: Lincoln Electric Pages: 16

Brand: Orion Pages: 52

DIGITIG 200DC MULTIPRO

Brand: Sherman digitec Pages: 18

Brand: Migomag Pages: 13

Brand: MSA Pages: 42

Plasma 40 Torch

Brand: BOC Pages: 12

Brand: Nussbaum Pages: 72

Brand: Redback Pages: 16

Brand: Global Lift Pages: 51

Brand: Keysight Pages: 46

Brand: M-system Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands