Joab EcoDrive LA Operation And Maintenance Manual Download Page 10

Page: 10 / 89

Correct Usage

Incorrect use of JOAB's products can lead to material fatigue and cause excessive wear to the
hydraulics and its components. The service life of the product can be reduced and in the worst-
case lead to breakdown.

Do not drive the vehicle with the hook lift

extended. It must be fully retracted.

Do not use the vehicle for any other

purpose than its intended use.

Make sure to reverse straight towards the

body. Do not reverse at an angle.

Do not lift loads that exceed the hook-

lift's specifications.

If the body becomes stuck, observe cau-

tion. The hooklift can easily be damaged.

About the Hook-Lift | Correct Usage

EcoDrive 2.0 manual: 1021970 Edition 1 | 2022-02-04

Summary of Contents for EcoDrive LA


























































































Search results

Summary of Contents for EcoDrive LA

Reviews:

Related manuals for EcoDrive LA

Brands by name

Popular brands

Joab EcoDrive LA, Operation And Maintenance Manual

Search results

Summary of Contents for EcoDrive LA

Reviews:

Related manuals for EcoDrive LA

Brands by name

Popular brands