background image

 

Do Žlábku 733, 514 01 Jilemnice

 

 
Subject: 

MTP Technical documentation 

 

Page No./No. of pages:  

17/20 

 
 

 
d) Check of V-belt tension and wear (as needed). 

 

e) Regular check of input filters (min. once a month) - if the heater is equipped with 
them  or  they  are  in  the  air-conditioning  line  with  the  heater.  When  clogged,  clean 
them  or  replace  the  filter  cloth.  Filter  clogging  time  depends  on  the  intake  air 

pollution. Clogging of the filters significantly reduces the amount of air supplied by 
the heater and increases the temperature of the heat exchanger chamber. The heat 
exchanger may be overheated and thus its service life may be reduced. 

 

f) Lubrication of fan bearings - applies only to some fans, e.g. fans with bearings for 
high temperatures (of ADH-RDH K / K2 type). 
Note:  for  MTP  (MTPAL)  standard  sets,  maintenance-free  bearings  with  permanent 
grease filling are used. 
 

           

 Defects: 

 

 

a) Overheating of heat exchanger, failure of safety thermostat T1 

- check whether the suction and discharge spaces (piping, ...) are passable 
- check fan condition, loose V-belts, seized bearings 

 

- check the filter cloth, or also filter inserts 

 

-  if  the filters  are  not  clogged,  it  is necessary  to  consult the  defect  with  the 

production plant. 

 

b) Flue gases flow into the heated space or higher oxygen content is measured in flue 
gases 

- check bolt tightening of the tube plate cover and the burner flange. 
- replace the seal of the burner flange and the tube plate cover. 
- check whether the combustion chamber is not burned. 

 

LIST OF ACCESSORIES AND SPARE PARTS

 

 
 

Spare  parts are  not  supplied  with the heater.  For  warranty repairs, the  spare parts 

are  available  at  the  production  plant  which  is  authorized  to  carry  out  warranty repairs  on 
the heater (except the burner). 
 

Post-warranty and non-warranty repairs are arranged by the customers themselves, 

the spare parts can be ordered at the production plant. 
 

The warranty does not apply to V-belts and filter cloths.

 

 

This  documentation  provides  the  basis  for  elaboration  of  operating  rules  in 

accordance with ČSN 386405.

 

 
 
 

Summary of Contents for MTP





















Reviews: