Jinova MTP Technical Documentation Manual Download Page 14 | Manualshive

Page: 14 / 20

background image

Do Žlábku 733, 514 01 Jilemnice

Subject:

MTP Technical documentation

Page No./No. of pages:

14/20

Do not install any elements that make it difficult to dismantle the panel covering the tube
plate cover.

The ESD3J safety thermostat is not designed to regulate the required temperature. It is
placed in the heated air behind the heat exchanger, in its upper part max. 20 cm behind the
heat exchanger tubes. The contact of the safety thermostat T1 must be connected to the
burner feed phase to ensure that it is switched off in any (even malfunctioning) condition of
the burner.

The contact of the operating thermostat T2 is connected to the control terminals

circuit (usually marked T1 and T2) of the burner and it switches it off when the temperature
is above the set value.

The contact of the fan thermostat T3 ensures switching on of the fan and its

slowdown

(cooling the combustion chamber) when the burner is switched off.

Recommended electrical connection, see drawing No.:

3-JH-2001C - for ESD3J electronic thermostat

The heater is equipped with a clamp for protective connection according to ČSN 32 2000

-

4.41.

For the outdoor design of the heater, the triple thermostat is provided with a cover.

Once connected, it is necessary to check the direction of speed of the fan engine!

In case of a triple thermostat, it is absolutely necessary to connect the clamp
with PE conductor to prevent the influence of any induced voltages on the
thermostat sensor.

Note:  It  is  not  possible  to  switch  off  the  whole  device  (both  burner  and  fans)
without  ensuring  fan  slowdown  to  cool  the  heat  exchanger.  The  heat
accumulated  in  the  heat  exchanger  could  damage  the  surrounding  equipment
due  to  the  flow!  It  must  not  be  possible  to  switch  off  the  fans  and  leave  the

burner on!

OPERATING INSTRUCTIONS

For the burner installed on the heat exchanger unit, the “Instructions” supplied

together with it by the manufacturer, apply to it.

Each heater is fitted at the output with a triple thermostat that provides safe

operating mode. This thermostat is not designed to regulate the required temperature.

«
...
12
13
14
15
16
...
»

Summary of Contents for MTP





















Reviews:

No comments

Related manuals for MTP

Brand: GE Pages: 28

Brand: NARVI Pages: 12

Brand: Garantia Pages: 2

ACQUITY UPLC I-Class IVD

Brand: Waters Pages: 98

Brand: Cordivari Pages: 44

Brand: Tiger Pages: 36

Brand: easy Maxx Pages: 37

Brand: Kozy-World Pages: 29

Brand: Scarlett Pages: 14

Brand: Bard Pages: 27

Brand: Seisco Pages: 20

Brand: lifeSMART Pages: 17

Brand: A.O. Smith Pages: 76

Brand: York Pages: 72

Brand: Mosebach Pages: 18

XCT 7 40VC009-048F-7G-QEE

Brand: Carrier Pages: 28

EUROSTOVE SRE 301 -

Brand: Eurostove Pages: 2

XtremeFLEX HSTAT-R Series

Brand: BriskHeat Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands