background image

8

SFP3-14-GB

www.jilong.com

II. Operation of the control valve

III. Draining procedure

III. Draining procedure

Warning: Before operation, make sure all corrugated 

tubes are properly connected and locked and the filter 

has been filled with the correct amount of sand.

Warning: Before operation, make sure the product is 

disconnected from the grounded receptacle protected 

by electrical leakage.

Warning: The control valve is provided with one closed 

valve position. Do not attempt to start the product when 

the control valve is in the closed position.

1.Make sure the product is powered-

off.

2.Remove the drain nuts (P3) first, 

then move the adapter (P4) at Port A 

and water pipe (P18) to Port D (see 

FIG. 12).

3.Press the control valve handle 

downwards and rotate it to the draining 

position, and then turn the power 

1.After the aforementioned preparations, the sand 

filter pump is ready for use. Set the filter function of 

the control valve.

2.Insert the plug into the matched receptacle to run 

the sand filter pump.

Note: During the operation of the sand filter pump, 

check the pressure reading of the manometer (P1).

Generally, when the pressure of the recommended 

1.When rotating the control valve, press the control valve 

handle first, then rotate the handle to the required position (see FIG. 11).

FIG. 12

FIG. 14

on. Perform draining until clean water is discharged (see FIG. 12). After 

draining, disconnect the power.

4.Rotate the control valve handle to backwashing position. Power on again, 

until clean water flows, then backwashing finishes. Disconnect power (see 

FIG. 12).

5.Remove the adapter (P4) at Port D and water pipe (P18) and return them 

to Port A (see FIG. 10).

6. Return the drain nut (P3) to Port D (see FIG. 10).

7.Power on and select the required function position. Begin operation.

Note: this step is for first operation only.

Note: do not attempt to set between two functions of the control valve to 

avoid possible leakage.

Summary of Contents for JL29P423NG













Reviews: