background image

2014

9

SFP3-14-GB

www.jilong.com

V. Sand Filter Pump Maintenance

VI. Motor and Slag Blocking Barrel Cleaning and Maintenance

Note: You must make sure that maintenance begins 

only after the sand filter pump is unplugged. 

Otherwise serious risks such as personal injury and 

even death may occur.

Note: Record the reading of the manometer during 

the operation of the sand filt er pump (see FIG. 15). 

When the manometer shows a pressure of 0.2bar 

(3psi) or higher, please clean up the sand bend 

or replace the sand. Use "backwash" and "rinse" 

functions.

Note: regular rinsing according to use situation is 

recommended.

1.It is essential to make sure the power cord is 

removed from the receptacle.

2.Block the water outlet of the pool.

3.Unscrew the slag blocking cover (P15) on the 

slag blocking barrel in an anticlockwise direction, 

take out the slag blocking screen (P13) and the 

seal ring (P14).

4.Rinse the slag blocking screen with a water 

pipe. If necessary, use a plastic brush to remove 

impurities. Do not use a metal brush.

5.Rinse the inside of the slag blocking screen 

and the seal ring of the slag blocking barrel with a 

water pipe

6.Install the seal ring (P14) of the slag blocking 

barrel, the slag blocking screen (P13) and the 

FIG. 15

sand filter pump is less than 0.2bar (3psi) (green area) (see FIG. 14), it 

runs normally.

cover (P15) of the slag blocking barrel in their original positions (see FIG. 

13).

Summary of Contents for JL29P423NG













Reviews: