JIB MJ10-1300E Instruction Manual Download Page 6 | Manualshive

Page: 6 / 33

JIB MJ10-1300E Instruction Manual Download Page 6

A. Crosscut Table-

Provides a wide, stable platform for supporting full-size panels during crosscutting

operations.

B. Flip Stops-

Used for quick measurements for crosscutting.

C. Crosscut Fence-

Used during crosscutting operations. Features a scale and multiple flip-style

stopblocks for precise, repeatable crosscutting operations.

E. Sliding Panel-

Conveniently glides the work-piece through the blade with effortless precision and

ease.

F. Blade Guard-

Fully-adjustable blade guard allows high visibility of the cutting operation while

maintaining maximum protection around the saw blade.

G. Rear extension table

H. Power Switch-

Start/stops the machine and has emergency stop function.

J. Blade Elevation Hand-wheel-

Adjust the height of the main saw blade.

K. Blade Angle Hand-wheel-

Adjust the angle of the saw blades.

L. Mitre Gauge-

This gauge aligns the wood for a cross-cut.

M. Rip Fence-

Fully adjustable with fine adjustments. Fence face can be positioned for standard cutting

operations, or in the lower position for blade guard clearance during narrow ripping operations.

N. Fence Assembly Lock Down lever-

Secures the fence assembly into position along the fence rail.

Q. Rip Fence Rail-

Provides the support for rip fence.

«
...
4
5
6
7
8
...
»

Summary of Contents for MJ10-1300E


































Reviews:

No comments