manualshive.com logo in svg

JIB MJ10-1300E, Instruction Manual, Page: 18 / 33

Share
Download
JIB MJ10-1300E Instruction Manual Download Page 18

 

size panels.   

 

 

 

 

 

 

 

With the crosscut fence mounted in the rear position, this machine also has the capability of crosscutting smaller 

panels. 

 

 
 
 
 
 
 
 
 
 

 

This machine has the capability of crosscutting workpieces while using the hold down w/mitre gauge .   

 

 

 

 

 

 

 

Lastly, this machine has the capability of crosscutting workpieces while using the rip fence as a cut-off gauge.   
 

 

 
 
 
 
 
 
 
 

 

Determine which cutting operation will be best suited for the workpiece to be crosscut.   

 

If you will be crosscutting full size panels, then skip ahead to "Crosscutting full size panels." 

 

If you will be crosscutting smaller panels, then skip ahead to "Crosscutting smaller panels." 

 

If you will be crosscutting workpieces using the hold down, then skip ahead to "Crosscutting using the hold down 
w/mitre gauge." 

 

  If you will be crosscutting workpieces using the rip fence as a cut-off gauge, then skip ahead to "Crosscutting using 
the rip fence as a cut-off gauge." 

 

 

Crosscutting full size panels:   

 

1. 

Mount the crosscut table to the sliding panel. 

 

 

Summary of Contents for MJ10-1300E


































Reviews:

No comments