JHCTech KMDA-3230 User Manual Download Page 55

Page: 55 / 76

User’s Guide

CSM Support

Compatibility Support Module, which is a compatibility module, is a special module of UEFI and

provides compatibility support for system that do not support UEFI.

GateA20 Active

This item indicates whether to disable GA20 through the BIOS server or keep the activation status all the

time.

Option ROM Messages

This item shows the display mode of option ROM Message.

Boot option filter

This item indicates the boot priority of controlling EFI or Legacy option ROM.

Network

This item is used to set the EFI network card Option ROM boot or the traditional network card Option

ROM boot or priority boot.

Storage

This item is used to set the EFI storage Option ROM boot or the traditional storage Option ROM boot.

Video

This item is used to set EFI display Option ROM startup or traditional display Option ROM startup.

Other PCI devices

This item is used to set the EFI PCI device Option ROM boot or the traditional PCI device Option ROM

boot.

Summary of Contents for KMDA-3230













































































Search results

Summary of Contents for KMDA-3230

Reviews:

Related manuals for KMDA-3230

Brands by name

Popular brands

JHCTech KMDA-3230, User Manual

Search results

Summary of Contents for KMDA-3230

Reviews:

Related manuals for KMDA-3230

Brands by name

Popular brands