background image

Jets™ 25MBA Vacuumarator™ pump

Tel. +47 70 03 91 00

www.jetsgroup.com

Product No. 200025004

Doc. Rev.: 22 (2021-06-08)

1

Vacuumarator™ pumps are the most compact efficient and reliable 
vacuum generators available for vacuum sanitary systems. The 
pump creates vacuum, macerates sewage and discharges in one 
single pass operation. 

Features:

● Highly efficient in transporting wastewater

● Small footprint and low weight allows for quick and flexible 

installation

● In line installation - direct discharge to sewer, STP (Sewage 

Treatment Plant) or collecting tank

● Multiphase design - pumps any combination of air, black and 

grey water

● Low energy consumption

● High quality – low lifecycle cost

Technical Data

...................................

Capacity

26 m³/h (ACMH) at 500 mbar abs. 60 Hz

(50% Vacuum)

......................................................................

Back Pressure

Max. 0.3 bar

..................................

Outside Dimensions

702 x 198 x 278 mm (LxWxH)

..............................................................................

Connection Inlet

DN50

...........................................................................

Connection Outlet

DN32

...............................................................................

Protection Class

IP 55

..............................................................

Insulation Class

155(F) to 130(B)

...........................................................................................

Duty

S1-100%

.............................................

Ambient Temperature Range

+0 °C - 55 °C

.............................................................................

Humidity

Class F / 95%

..............................................................

Approvals

Motor - CSA Approved

..................................................................................

Net Weight

66.50 kg

Operating Data

....................................................................................

Frequency

// 60 Hz

................................................................................

Voltage

// Δ198-218 V

.........................................................................

Nominal Current

// 12.9  A

...........................................................................

Speed

CCW // 3435 rpm

...........................................................................

Power Output

// 3.45 kW

.......................................................................

Power Factor

// 0.88  cos ɸ

.....................................................................................

Efficiency

// 84.5%

...............................................................

Heat Dissipation

Approx. 0.6 kW

Disclaimer

Note: Our products and services are offered and sold subject to Jets 
Vacuum AS’ General Sales Conditions, copies of which will be 
furnished upon request. Information provided herein is solely for 
information purposes, does not constitute any warranty or 
representation of any kind and is subject to change without notice. 
We strive to reproduce product colors reasonably accurate. Without 
prior written approval, this document or any part of may not be 
reproduced in any form. Jets™, Vacuumarator™, Helivac™, VC™, 
VOD™, CVS™ and Softsound™ are trademarks and/or registered 
trademarks of Jets. © Jets AS. All rights reserved.

Summary of Contents for 25MBA


















Reviews: