Jesco C 2213 Operation & Maintenance Instructions Manual Download Page 41 | Manualshive

Page: 41 / 44

background image

Warranty Application

| Operation Manual C 2213 |

41

17 Warranty Application

Warranty Application

Please copy and send it back with the unit!

If the device breaks down within the period of warranty, please return it in a cleaned condition with the
complete warranty application, filled out.

Sender

Company: .......................................................

Phone.: ..........................

Date: .............................

Address: .....................................................................................................................................................

Contact person: ..........................................................................................................................................

Manufacturer order no.: ..................................

Date of delivery: ...........................................................

Device type: ...................................................

Serial number: .............................................................

Nominal capacity / nominal pressure: ..........................................................................................................

Description of fault: .....................................................................................................................................

...................................................................................................................................................................

...................................................................................................................................................................

...................................................................................................................................................................

...................................................................................................................................................................

...................................................................................................................................................................

...................................................................................................................................................................

Service conditions of the device

Point of use / system designation: ...............................................................................................................

...................................................................................................................................................................
...................................................................................................................................................................

Accessories used (suction line etc.): ............................................................................................................

...................................................................................................................................................................
...................................................................................................................................................................
...................................................................................................................................................................

Commissioning (date): ...........................................
Duty period (approx. operating hours): ...................

Please describe the specific installation and enclose a simple drawing or picture of the chemical feed
system, showing materials of construction, diameters, lengths and heights of suction and discharge lines.

«
...
39
40
41
42
43
...
»

Summary of Contents for C 2213













































Reviews:

No comments

Related manuals for C 2213

Brand: Valve Concepts Pages: 16

Brand: Saitek Pages: 4

Brand: Camozzi Pages: 33

Brand: Camozzi Pages: 2

Brand: Camozzi Pages: 64

Brand: Febco Pages: 12

Brand: GameSir Pages: 8

Brand: Game ready Pages: 21

Brand: VAMP Pages: 304

Brand: Tactical Pages: 8

Brand: Hanna Instruments Pages: 88

Black Force Wireless

Brand: Hama Pages: 10

Brand: Zeta Pages: 44

TruPortal TP-ADD-1DIP

Brand: Interlogix Pages: 9

Brand: Argo-Hytos Pages: 38

Brand: Anest Iwata Pages: 8

Brand: Paser Pages: 2

Brand: Eaton Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands