Jenn-Air JES8750BA Series Page 24 Service Manual Download | Manualshive

Page: 24 / 67

background image

Testing Procedures

!

WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless
testing requires power.

24 16026926

© 2006 Maytag Services

"

Quick Test

"

Mode for EOC III

Follow the procedure below to perform the EOC III quick test. Once the control is in the quick test mode, any relay
may be activated in any sequence. The test mode will be exited after 10 minutes of inactivity (no pads pressed
within 10 minutes).

1. Press

the

Setup

pad, then press the right

ATM

pad.

2. Press

the

left

ATM

pad, then press and hold

Back

and

Enter

pads for 5 seconds to enter SERVICE menu options.

3. Press the right

ATM

pad to scroll to the TEST menu.

4. Press

the

left

ATM

pad to select TEST options.

5. Press

the

left

ATM

pad again to enter the

"

Quick Test

"

mode.

6. Press each of the following pads indicated in the table below.
7. Press

Cancel

or

Setup

pads to exit.

NOTE:

Press and hold the applicable pad to activate the associated response.

Release the applicable pad to deactivate the associated response.

The control automatically enters the engineering mode so visual feedback of relay operations is available on the

control display. Any time a load is activated, the cooling fan is activated. When the load is deactivated, the cooling
fan is also deactivated.

Display will indicate the following:

Pad Response

BAKE....................................................Bake relay activated.
BROIL ..................................................Broil relay activated.
CONVECT............................................Convection Bake and Cooling Fan relays activated.
OVEN LIGHT .......................................Oven light relay activated.
RAPID PREHEAT ................................Convection Fan (HIGH/LOW) activated.
WARMING ZONE ................................Warming Zone relay activated.
VENT (DOWNDRAFT) FAN ................Vent Fan relay activated.
CLEAN .................................................Motorized Door Lock relay activated.
SETUP .................................................1 Second Beep.
FAN ......................................................Downdraft Fan (HIGH/LOW) relay activated.
WARMING DRAWER ..........................Warming Drawer (HIGH/LOW) relay activated.

Oven Sensor and Meat Probe Resistances

OVEN SENSOR

Sensor Type:

RTD

1000

Ω

platinum

Calibration:

1654

Ω

(350° F/177° C)

Temperature F (C)

Resistance (Ohms)

100 (38)

1143

200 (94)

1350

300 (149)

1553

350 (177)

1654

400 (204)

1753

500 (260)

1949

600 (316)

2142

700 (371)

2331

800 (427)

2516

900 (483)

2697

1000 (538)

2874

MEAT PROBE

Type:

NTC

Thermistor

Calibration:

9938

Ω

(150° F/65.5° C)

Temperature F (C)

Resistance (Ohms)

32 (0)

163300

68 (20)

62450

95 (35)

32660

122 (50)

18020

158 (70)

8760

185 (85)

5360

212 (100)

3400

«
...
22
23
24
25
26
...
»

Summary of Contents for JES8750BA Series




































































Reviews:

No comments

Related manuals for JES8750BA Series

Heritage HGER30S

Brand: Dacor Pages: 20

Brand: Lang Pages: 20

TRATIS36SS600-B

Brand: Faber Pages: 40

Brand: Garland Pages: 2

Brand: John Lewis Pages: 2

Brand: Avantco Pages: 8

PGB916DEMBB - Profile 30" - Convection Gas R

Brand: GE Pages: 2

Brand: GE Pages: 2

Brand: GE Pages: 24

Brand: GE Pages: 36

Brand: GE Pages: 36

Brand: GE Pages: 48

Brand: GE Pages: 48

Brand: GE Pages: 33

Brand: GE Pages: 56

Brand: GE Pages: 56

Monogram ZGU484NGP5SS

Brand: GE Pages: 40

Brand: GE Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands