JEI MAGBEAST HM40 Operation & Safety Manual Download Page 26

Page: 26 / 26

JEI SOLUTIONS LTD

MAGBEAST HM40

5.2 (20130122)

Operators manual for Drilling Machine Magbeast HM40

- 26 -

10. WARRANTY CARD

WARRANTY CARD No

.............

…………………………………………………………….. in the name of

Manufacturer warrants the Drilling Machine to be free of defects in material and

workmanship under normal use for a period of 12 months from date of sold.

This warranty does not cover cutters, damage or wear arises from misuse,

accident, tempering or any other causes not related to defects in workmanship or

material.

Date of Production .......................................... Serial No ..............................................

Quality Control: ..............................................................................................................

Date of Purchase: ..........................................................................................................

Signature of Seller:

…………………………………………………………………………..

Summary of Contents for MAGBEAST HM40



























Search results

Summary of Contents for MAGBEAST HM40

Reviews:

Related manuals for MAGBEAST HM40

Brands by name

Popular brands

JEI MAGBEAST HM40, Operation & Safety Manual

Search results

Summary of Contents for MAGBEAST HM40

Reviews:

Related manuals for MAGBEAST HM40

Brands by name

Popular brands